NCR 6003-K001-V003 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 163

background image

6

WAYNE VISTA DISPENSER

1)

Locate Side B of the dispenser.

Note: For the purposes of this procedure, Side B of the dispenser refers to the side
without the manufacturer’s label/Serial Number Plate.
Note: References to “left-hand” and “right-hand” are as viewed into the pump on the
Side the installer is working on.
2)

Use a Wayne Security Key to unscrew the two security bolts (Figure 2) at the top left
and top right of the electronics head bezel.

Figure 2

3)

Lower the electronics head bezel by pulling the top forward until it fully rests on the
suspension cables.

4)

Acquire the heater (NCR heater assembly) and OPTIC heater wire guard (497-
0522796).

Note: For Vista, the power supply bracket can remain mounted to the inner dispenser
wall during installation of the heater in the following steps, even though the pictures
below do show the power supply bracket removed from the dispenser during heater
installation.
5)

Slide the wire guard (497-0522796) around the NCR heater assembly so that the
edge of the bracket aligns with the Advantage, Vista, Encore, Eclipse, Tokheim B
alignment mark as shown in Figure 3 and Figure 4.

«
...
18
19
20
21
22
...
»

Содержание 6003-K001-V003




































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 6003-K001-V003

Бренд: M-system Страницы: 3

Бренд: Fein Страницы: 248

Бренд: ZF Страницы: 30

Бренд: Raymarine Страницы: 111

Бренд: ParaBody Страницы: 4

Бренд: York Fitness Страницы: 34

Бренд: Hach Страницы: 66

Бренд: Hach Страницы: 14

Бренд: Hach Страницы: 144

QuikChem 8500 2 Series

Бренд: Hach Страницы: 80

Бренд: Hach Страницы: 178

Бренд: Hach Страницы: 32

Бренд: hager Страницы: 4

Бренд: Idmed Страницы: 2

Бренд: Raytheon Страницы: 68

Бренд: KegLand Страницы: 23

Бренд: PAS Systems International Страницы: 24

MARK V Alcovisor

Бренд: PAS Systems International Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды