NCR 6003-K001-V003 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 163

background image

v

OUT OF BOX FAILURE (OBF)

If you experience an out of box failure (OBF) during installation or staging related to a
missing, wrong or defective unit or item, simply provide NCR with a detailed description
of the issue and the item will be replaced free of charge. For assistance with this
process send an email to

[email protected]

with the following details:

•

NCR Sales Order # (Sales Order # are located on the box)

•

Date of Product Installation

•

Product Model #

•

Unit Serial #

•

NCR part # of defective/missing/wrong component

•

Description of Failure (please be specific. For example: “display will not power
on”)

•

Customer/Requestor’s contact name, phone number and/or e-mail address

•

Address to ship replacement part(s)

Transport the product in its original packaging to prevent impact damages.
If you do not have access to a computer, you may leave a voice message at: 1-800-528-
8658 (USA), or (International) +1-770-623-7400. When leaving a message, please
provide a phone number and/or an email address so NCR can contact you if additional
details are needed.
Note: Used equipment that experiences a failure does not qualify as an OBF and
should go through the NCR warranty process.

«
...
7
8
9
10
11
...
»

Содержание 6003-K001-V003




































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 6003-K001-V003

Бренд: Danelec Страницы: 67

Бренд: York Fitness Страницы: 20

Бренд: Haag-Streit Страницы: 18

Бренд: Haag-Streit Страницы: 20

Бренд: V-TEK Страницы: 2

Бренд: V-TEK Страницы: 112

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Страницы: 12

Бренд: Hanil Страницы: 24

Бренд: Hanil Страницы: 32

Бренд: Hanil Страницы: 24

Бренд: Qlight Страницы: 4

Бренд: PAT Страницы: 44

Бренд: Park Tool Страницы: 4

Бренд: Qlight Страницы: 4

EVENTWASH VL800

Бренд: Vari Lite Страницы: 23

Бренд: Vapotherm Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды