NCR 6003-K001-V003 Скачать руководство пользователя страница 81

Страница: 81 / 163

Figure 118

Caution: After all cables are reconnected, double check that no cables are hanging or
lying in front of the heater exit.
13)

Any remaining cables hanging in front of the heater or lying in front of the heater
exit should be re-routed and restrained using one of the additional supplied cable
ties (006-8616073).

Warning:

Heater surfaces are hot! Do not touch!

14)

All wires are to be routed away from any sharp edges and door joints/gaskets.

15)

Swing the OPTIC door shut

16)

Use the TPX88 Tokheim key to lock the OPTIC door after ensuring that all cables are
secured behind the OPTIC unit.

Tokheim Premier C NARROW Installation

Identify the A Side of the dispenser. To determine Side A on the Premier Dispenser:
a)

Look at the base of the dispenser.

Locate the Model/Serial number plate on one of the dispenser sides (the U.L.
and F.C.C. plates are nearby) and stand facing it.

You are looking at SIDE A. See Figure 119

Содержание 6003-K001-V003




































































































































































Результаты поиска

Содержание 6003-K001-V003

Отзывы:

Похожие инструкции для 6003-K001-V003

Бренды по названию

Популярные бренды

NCR 6003-K001-V003, Руководство по установке

Результаты поиска

Содержание 6003-K001-V003

Отзывы:

Похожие инструкции для 6003-K001-V003

Бренды по названию

Популярные бренды