Checking the LED display at the receiver R-18 and R-CAN:
(Optional with integrated charger)
The green LED flashes:
RADIO PRESENT.
If the LED fails to come on:
1. Check that the transmitter is on.
2. Check the power supply of the receiver.
3. (Optional) Irregular flashing of the LED:
Check or change the current radio channel.
Checking the LED display at the receiver Compact-M:
(Without integrated charger)
The green LED flashes:
RADIO PRESENT.
If the LED fails to come on:
1. Check that the transmitter is on.
2. Check the power supply of the receiver.
3. (Optional) Irregular flashing of the LED:
Check or change the current radio channel.
Service plug:
For NBB service only.
Checking the LED's at the receiver PNN-BUS-3:
%
LED1:
POWER ON. If LED fails to come on, check the power supply.
If the power lead is OK, call in the after-sales service.
%
LED2:
HF PRESENT. Steady light when transmitter is switched on
(insignificant for scanner operation).
%
LED3:
Flashes evenly during fault-free operation.
Irregular flashing means that the HF channel is probably at fault -
please set another channel.
%
LED4:
If this LED comes on, the HF channel is at fault.
%
LED5:
Charge condition display of battery (only present when charger is
integrated). Steady light when charging a battery.
LED flashes: The battery is charged, the charging process is finished.
Checking the LED's at the receiver Compact-V:
%
LED 1 green:
POWER ON. If LED fails to come on, check the power supply.
If the power lead is OK, call in the after-sales service.
%
LED 2 yellow:
HF PRESENT. Steady light when transmitter is switched on
(insignificant for scanner operation).
%
LED 3 green:
Flashes evenly during fault-free operation.
Irregular flashing means that the HF channel is probably at
fault - please set another channel.
%
LED 4 red:
If this LED flashes, the HF channel is at fault (not in the
scanner operation).
Steady light notifies the operator that an output function
is critical due to over current.
®
MADE IN GERMANY
3.820.1008
®
ZULASSUNG - TYPE APPROVAL - AGREMENT - HOMOLOGATION
I
SYSTEM
NON EU COUNTRIES
:
AUS
CDN
CH
CZ
H
IS
KO
N
EU COUNTRIES
:
X
0560
no approval necessary
2634 231 116A /
2634 231 116
BAKOM 95.0720.K.P
45251983
MÜ-40.039-083/96
IS-3236-00
93335
NO96000433-R /
NO95000545-R
1027/96
YK33-9806
K9VPOC90 T001 /
K9VPNN3-5R001 /
O5RS-DE96AO
3K43D/3R1B9/
SPLS/RX-439/98
PL
TJY
USA
ZA
1
2
3
4
5
COMPACT-M
R-18
R-CAN
Receiver Type / Version:
Factory No.:
Frequency:
PNN-BUS-3
999 899 4990
400 -477 MHz
X
SERVICE PLUG
LED RADIO ON
LED RADIO ON
SERVICE PLUG
1 2 3 4
www.nbb.de
®
COMPACT-V
X
3.820.1195
LEDS
SERVICE PLUG
To maintain operational safety, a regular function check of the NBB radio remote control is
necessary. In single-shift day-to-day operation, we recommend performing this check at
least once a week. Checking is possible using the display lights provided on the receiver.
To do so, the transmitter must be set to the ready-to-operate state.
First connect just the receiver - the transmitter remains switched off.
%
Activate the transmitter by pressing the "STOP" key, resp. the key "START/ ON/
HORN".
%
Now check the commands (always start with the lowest stage) and check for cor-
rect function of the unit to be controlled.
%
Ensure in particular that there is nobody in the danger area.
ACCIDENT RISK!
%
STOP
,
check
. Press the STOP key at the transmitter until the switch engages.
Then observe if the unit to be controlled is switched off (time to switch off accor-
ding to the application).
6. FUNCTION CHECK
