Nautilus NS-700, Инструкция по сборке, Страница: 14 / 25

NS-700
13
step
10
Step #10 Materials:
# Component Qty
58 4 1/2" Pulley 14
61 Double Floating Pulley Bracket 2
62 Cable Retaining Bracket 1
68 Snap Cap 2
69 Cable #1 - Pull down Cable 263.75"L 1
80 Hex Bolt - 3/8" x 2 3/4"L 4
82 Hex Bolt - 3/8" x 2"L 8
85 Cap Head Allen Screw 3/8" x 3"L
with thread lock
2
95 3/8" Flat Washer 16
97 3/8" Lock Nut 12
100 Step Spacer 19/32"H 8
A. Thread one end of Cable #1 (69) into the Selector Rod/Top Plate
Assembly as shown in Detail A. Do not tighten locking nut.
B. Draw Cable #1 (69) over a 4 1/2” Pulley (58) and place it in the
Pulley Bracket (36) making sure that the lower section on the
Pulley Bracket is between the guide rods. Attach the Pulley to the
Pulley Bracket using the hardware shown. Tighten hardware securely.
C. Loop Cable #1 (69) around a 4 1/2” Pulley (58) and attach the
pulley to the Rear Top Frame (2) using the Cable Retaining
Bracket (62) and the hardware shown. Tighten hardware securely.
D. Loop Cable #1 (69) around a 4 1/2” Pulley (58) and attach the
pulley to the bracket on the Rear Top Frame (2) using the hardware
shown. Proceed by looping the cable around another 4 1/2”
Pulley (58) and attaching it to inner hole of the Double Floating
Pulley Bracket (61) using the hardware shown. Tighten hardware
securely.
E. Loop Cable #1 (69) around a 4 1/2” Pulley (58) and attach the
pulley to the second bracket on the Rear Top Frame (2) using the
hardware shown. Proceed by looping the cable around another 4
1/2” Pulley (58) and attach it to the top bracket on the Front
Upright (7) using the hardware shown. Tighten hardware securely.
F. Loop Cable #1 (69) around a 4 1/2” Pulley (58) and attach the
pulley to the bracket on the Top Beam (6) using the hardware
shown. Proceed by looping the cable around another 4 1/2” Pulley
(58) and attaching it to the outer hole of the Double Floating
Pulley (61) using the hardware shown. Tighten hardware securely.
G. Draw Cable #1 (69) over a 4 1/2” Pulley (58) and place the pulley
in the slot on the Front Upright (7) using the lower hole. Attach
the pulley with the hardware shown in Detail B. Tighten hardware
securely.
H. Loop Cable #1 (69) around a 4 1/2” Pulley (58) and place it in the
Press Arm Support Assembly (22). Attach the pulley using the
lower hole with the hardware shown in Detail B. Tighten Hardware
securely.
I. Loop Cable #1 (69) around a 4 1/2” Pulley (58) and place the
pulley in the slot on the Front Upright (7) using the upper hole.
Attach the pulley using the hardware shown in Detail B. Proceed
by looping the cable around another 4 1/2” Pulley (58) and
attaching the pulley to the top hole in the Press Arm Support
Assembly (22) using the hardware shown in Detail B. Tighten
hardware securely.
J. Loop Cable #1 (69) around a 4 1/2” Pulley (58) and attach the
pulley to the Top Beam (6) using the hardware shown in Detail C.
Tighten hardware securely. NOTE: Leave the end of the cable
inside the Top Beam tube.
K. Feed Cable #1 (69) through the Top Beam tube and out the front
slot. Draw cable around a 4 1/2” Pulley (58) and attach the pulley
in the front slot using the hardware shown in Detail C. Tighten
hardware securely.
L. Attach Snap Caps (68) in the Press Arm Support Assembly (22)
as shown.