background image

Page 3

5. 

All equipment MUST be secured (bolted and 
tightened) to a solid, level surface, using all of 
the anchoring holes provided, to stabilize and 
eliminate rocking or tipping over. Shim any 
mounting surface that does not rest thoroughly 
on the fl oor using fl at washers, DO NOT force the 
foot to contact the ground with anchors.

Fasteners must have a minimum of 500 lbs. 
tensile capacity, be a bolt of grade 2 or better 
and be installed per the bolt manufacturer’s 
specifi cations.

WARNING:

 Due to the wide variety of fl ooring 

on which equipment may be anchored or installed 
and differences in applicable local building codes, 
Core Health & Fitness is not responsible for any 
damage to the fl ooring that may result due to 
anchoring or installing equipment to the fl oor and 
for compliance with local building codes. Only 
licensed contractors or certifi ed installers should 
be used to insure proper anchoring, installation, 
and compliance with local building code.

6. 

Do not exceed the maximum allowable user 
weight limit of:

•  350 lbs. (160 kg.)

7. 

It is the purchaser’s sole responsibility to properly 
instruct its end users and supervising personnel 
as to the proper operating procedures of all 
equipment. 

8. 

 Caution: unit is heavy and requires two people 

for assembly.

SAVE THESE INSTRUCTIONS

Содержание HDP6D-LFHR













Отзывы: