background image

10

Condition/Problem

Things to Check

Solution

No display/partial display/

unit will not turn on

Check electrical (wall) 

outlet

Make sure unit is plugged into a functioning wall outlet.

Check connection at front 

of unit

Connection should be secure and undamaged. Replace adapt-

er or connection at unit if either are damaged.

Check data cable integrity All wires in cable should be intact. If any are visibly crimped or 

cut, replace cable.

Check data cable

connections/orientation

Be sure cable is connected securely and oriented properly. 

Small latch on connector should line up and snap into place.

Check console display for 

damage

Check for visual sign that console display is cracked or other-

wise damaged. Replace Console if damaged.

Console Display

If Console only has partial display and all connections are fine, 

replace the Console.
If the above steps do not resolve the problem, contact Cus-

tomer Service (if inside US/Canada) or your local distributor (if 

outside US/Canada)

.

Speed displayed is not 

accurate

Check Speed Sensor 

Magnet position

Speed Sensor Magnet should be in place on Flywheel.

Speed displayed is always 

“0”/stuck in Pause mode

Data cable

Make sure the data cable is connected to the Console and the 

main frame assembly.

Speed Sensor

Make sure the RPM Sensor Magnet and the RPM Sensor are 

in place.

No Speed/RPM reading

Check data cable integrity All wires in cable should be intact. If any are cut or crimped, 

replace cable.

Check data cable 

connections/orientation

Be sure cable is connected securely and oriented properly. 

Small latch on connector should line up and snap into place.

Check Speed Sensor 

Magnet position

Speed Sensor Magnet should be in place on Flywheel. 

Check Speed Sensor 

Assembly

Speed Sensor Assembly should be aligned with magnet and 

connected to data cable. Realign sensor if necessary. Replace 

if there is any damage to the sensor or the connecting wire.

Unit operates but 

Bluetooth

®

 Heart Rate 

(HR) not displayed

Bluetooth

®  

Heart Rate 

Sensing Device (Armband 

provided with IC4)

Make sure device is directly against skin and contact area is 

wet.

Bluetooth

®  

Heart Rate 

Sensing Device Batteries

If device has replaceable batteries, install new batteries.

Interference

Try moving unit away from sources of interference (TV, Micro-

wave, etc). 

Replace Heart Rate Sens-

ing Device

If interference is eliminated and HR does not function, replace 

device.

Replace Console

If HR still does not function, replace Console.

Unit operates but 

Bluetooth

®

 HR displayed 

incorrectly

Connected to previous 

user

The Console may be still connected to the previous user. Push 

Connect Bluetooth

®

 button to disconnect from them/ connect to 

your Heart Rate Sensing Device.

Troubleshooting

Содержание Bowflex C6



















































































Отзывы: