17
Nautilus NS700X
#
component
Qty
58 4 1/2” Pulley
14
61 Double Floating Pulley Bracket
2
62 Cable Retaining Bracket
1
68 Snap Cap
2
69 Cable #1 - Pull down Cable 263.75”L
1
80 Hex Bolt - 3/8” x 2 3/4”L
4
82 Hex Bolt - 3/8” x 2”L
8
85 Cap Head Allen Screw 3/8” x 3”L
with thread lock
2
95 3/8” Flat Washer
16
97 3/8” Lock Nut
12
100 Step Spacer 19/32”H
8
Step 10 Components:
Procedure:
a.
Thread one end of Cable #1 (69) into the Selector Rod/Top Plate Assembly as shown in
Detail A. Do not tighten locking nut.
B
. Draw Cable #1 (69) over a 4 1/2” Pulley (58) and place it in the Pulley Bracket (36) making sure
that the lower section on the Pulley Bracket is between the guide rods. Attach the Pulley to
the Pulley Bracket using the hardware shown. Tighten hardware securely.
c
. Loop Cable #1 (69) around a 4 1/2” Pulley (58) and attach the pulley to the Rear Top Frame (2)
using the Cable Retaining Bracket (62) and the hardware shown. Tighten hardware securely.
D.
Loop Cable #1 (69) around a 4 1/2” Pulley (58) and attach the pulley to the bracket on the Rear
Top Frame (2) using the hardware shown. Proceed by looping the cable around another 4 1/2”
Pulley (58) and attaching it to inner hole of the Double Floating Pulley Bracket (61) using the
hardware shown. Tighten hardware securely.
e.
Loop Cable #1 (69) around a 4 1/2” Pulley (58) and attach the pulley to the second bracket on
the Rear Top Frame (2) using the hardware shown. Proceed by looping the cable around
another 4 1/2” Pulley (58) and attach it to the top bracket on the Front Upright (7) using the
hardware shown. Tighten hardware securely.
f
. Loop Cable #1 (69) around a 4 1/2” Pulley (58) and attach the pulley to the bracket on the Top
Beam (6) using the hardware shown. Proceed by looping the cable around another 4 1/2” Pul
ley (58) and attaching it to the outer hole of the Double Floating Pulley (61) using the hardware
shown. Tighten hardware securely.
G
. Draw Cable #1 (69) over a 4 1/2” Pulley (58) and place the pulley in the slot on the Front Up
right (7) using the lower hole. Attach the pulley with the hardware shown in Detail B. Tighten
hardware securely.
H.
Loop Cable #1 (69) around a 4 1/2” Pulley (58) and place it in the Press Arm Support
Assembly (22). Attach the pulley using the lower hole with the hardware shown in Detail B.
Tighten Hardware securely.
i.
Loop Cable #1 (69) around a 4 1/2” Pulley (58) and place the pulley in the slot on the Front
Upright (7) using the upper hole. Attach the pulley using the hardware shown in Detail B.
Proceed by looping the cable around another 4 1/2” Pulley (58) and attaching the pulley to the
top hole in the Press Arm Support Assembly (22) using the hardware shown in Detail B.
Tighten hardware securely.
J.
Loop Cable #1 (69) around a 4 1/2” Pulley (58) and attach the pulley to the Top Beam (6) using
the hardware shown in Detail C. Tighten hardware securely. NOTE: Leave the end of the cable
inside the Top Beam tube.
K
. Feed Cable #1 (69) through the Top Beam tube and out the front slot. Draw cable around a 4
1/2” Pulley (58) and attach the pulley in the front slot using the hardware shown in Detail C.
Tighten hardware securely.
l.
Attach Snap Caps (68) in the Press Arm Support Assembly (22) as shown.
ASSEmBLY
STEP 10
(See Diagram On Next Page)
