Naturela NHC-H42-2 Скачать руководство пользователя страница 10

* End of the first interval (timer) that allows the heater's work

* Start of the second interval (timer) that allows the heater's work

* End of the second interval (timer) that allows the heater's work

* Start of the third interval (timer) that allows the heater's work

* End of the third interval (timer) that allows the heater's work

Error messages

If no intervals that allow the heater's work are activated, pressing the 

View/Enter 

button skips 

this information.

Possible error messages:

No Errors

 – No registered errors

Anode Low 

– Reduced size of the anode protector. A check is required.

Leakage

  –  A   leakage   from   the   electrical   heater   to   the   water   heater's   hull   is 

registered. In this case it turns off and the next turning on is possible only after 
turning it off from the electrical power panel.

No heat

 – The heater is on, but the temperature in the water heater is not increasing

S1 E1

 – A breakdown in the temperature sensor in the bottom section of the water 

heater. It is broken or disconnected.

S1 E2

 – A breakdown in the temperature sensor in the bottom section of the water 

heater. It is on short circuit.

S1 Frost

 – On turning on the power, the temperature of the water in the water heater 

is negative and it is possible to be frozen. Must check the tank's wholeness before 
turning on the power again.

S2 E1

 – A breakdown in the temperature sensor in the top section of the water heater. 

It is broken or disconnected.

S2 E2

 – A breakdown in the temperature sensor in the top section of the water heater. 

It is on short circuit.

S2  Frost

  –  The temperature sensor in the top section of the water heater registers 

negative temperature.

S3 E1

  –  A breakdown in the temperature sensor of the collector. It is broken or 

disconnected. Only modes with electrical heating and boiler heating will work. 

In 

this   case   the   solar   installation's   circulation   pump   works   constantly   to   avoid 
overheating of the solar collector!!!

S3 E2

 – A breakdown in the temperature sensor of the collector. It is on short circuit. 

Only modes   with electrical heating and boiler heating will work. 

In this case the 

NHC-H42-2 Reference Manual ver 1.6

стр. 10 / 18

Содержание NHC-H42-2



















Отзывы: