manualshive.com logo in svg

National 5200 PANTHER, Инструкция по эксплуатации

Поделиться
Скачать
National 5200 PANTHER Скачать руководство пользователя страница 86

Page 63

5200 & 5200QL ACCESSORIES

7074 TILE BOX 

The Tile Box works for wind rowing and assists
for a fast clean-up and collection of tile debris for
quick removal. High abrasion alloy for a long
lasting edge. Resharpens just like a blade. 5'' x
27'' x 6'' box.  Attaches to the #7050-27 Cutting
Head (required).

5110-100 FRONT WHEEL ASSEMBLY

Allows stability and safe transportation over any
surface. Easy and quick to attach.

5110-100W Replacement Wheel Only

5205 BATTERY CHARGER

5205

Battery Charger 24 Volt, 110 V

5205-W

Battery Charger 24 Volt, 220/240, CE Approved

For use with #5203 and/or #5204 Power Packs

5212

Battery Charger 48 Volt, 50/60 Cycle, 100 to 240 Volt

NOTE: O

NLY USE WITH

#5204 P

OWER

P

ACKS

7050-15 CUTTING HEAD EXTENSION

Extension for cutting heads to reach under tight
areas. 

5110-111-3 OPTIONAL ARM RESTS/ SET 

Optional Arm Rests for added comfort. Set
includes left and right arm rest and mounting
hardware.

5205

5212

5207-4 SPLITTER

To use with #5212 48 volt charger.

NOTE: DO NOT

use with any other charger.

Содержание 5200 PANTHER





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды