National Instruments VXIpc 600 Series Скачать руководство пользователя страница 25

Страница: 25 / 88

Chapter 3

Configuration and Installation

National Instruments Corporation

3-5

VXI/VMEpc 600 Series User Manual

Table 3-1 lists the factory-default settings and options for the onboard
jumpers and switches.

Note

Please do not adjust the jumpers on any jumper blocks not listed in Table 3-1
unless directed by National Instruments support.

Table 3-1.

VXI/VMEpc 600 Series Hardware Default Settings

Jumper

Default Setting

Optional Setting

Enable MITE
self-configuration

Disable MITE
self-configuration

No termination on
external trigger input

Terminate external trigger
input to 50

Ω

Supply SCSI termination

Disable SCSI termination

Receive CLK10 input
from SMB

Source CLK10 output to
SMB

No termination on CLK10
input

Terminate CLK10 input
to 50

Ω

Source CLK10 from
onboard oscillator

Source CLK10 from SMB

Non-inverted CLK10
output

Inverted CLK10 output

MITE user configuration

MITE factory
configuration

W11

Enable automatic slot
detection

Force System Controller;
Force Non-System Cont.

W20

Normal CMOS operation

Clear CMOS

Содержание VXIpc 600 Series

























































































Результаты поиска

Содержание VXIpc 600 Series

Отзывы:

Похожие инструкции для VXIpc 600 Series

Бренды по названию

Популярные бренды

National Instruments VXIpc 600 Series, Руководство пользователя

Результаты поиска

Содержание VXIpc 600 Series

Отзывы:

Похожие инструкции для VXIpc 600 Series

Бренды по названию

Популярные бренды