National Instruments VXIpc 600 Series Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 88

background image

Chapter 3

Configuration and Installation

VXI/VMEpc 600 Series User Manual

3-6

©

National Instruments Corporation

Configuring the VXI/VMEpc 600 Series

This section describes how to configure the following options on the
VXI/VMEpc 600 Series:

•

VXI/VMEbus System Controller/Non-System Controller

•

VXIbus CLK10 routing (VXIpc only)

•

Trigger input termination (VXIpc only)

•

MITE EEPROM

VXI/VMEbus System Controller/Non-System Controller

The VXI/VMEpc 600 Series is configured at the factory to automatically
detect if it is installed in Slot 0 of a VXIbus mainframe (or Slot 1 in a
VMEbus chassis). With automatic System Controller slot detection, you
can install the module into any VXI/VMEbus slot.

You can manually configure the VXI/VMEpc 600 Series for either
System Controller or Non-System Controller operation by defeating the
automatic-detection circuitry. Use the three-position jumper W11 to select
automatic detection, System Controller, or Non-System Controller
operation. Figure 3-4 shows these three settings.

Caution

Do not install a device configured for System Controller into another slot without
first reconfiguring it to either Non-System Controller or automatic-detection
configuration. Neglecting to do this could result in damage to the device, the
VXI/VMEbus backplane, or both.

Figure 3-4.

System Controller Slot Configuration

!

W11

a. Manual Configuration

for Non-System Controller

Not

SYSCTRL

Auto

SYSCTRL

Not

SYSCTRL

Auto

SYSCTRL

Not

SYSCTRL

Auto

SYSCTRL

W11

b. Automatic System

Controller Slot

Detection (Default)

W11

c. Manual Configuration

for System Controller

«
...
24
25
26
27
28
...
»

Содержание VXIpc 600 Series

























































































Отзывы:

Нет отзывов

Похожие инструкции для VXIpc 600 Series

Бренд: Nelsen Corporation Страницы: 16

Бренд: National Instruments Страницы: 34

Бренд: Valve Concepts Страницы: 16

Max Charge MC-624

Бренд: Balmar Страницы: 8

MAX CHARGE MC-614

Бренд: Balmar Страницы: 20

Бренд: Bard Страницы: 8

Бренд: Bardiani Valvole Страницы: 35

Бренд: Danfoss Страницы: 20

Бренд: Danfoss Страницы: 36

Бренд: Danfoss Страницы: 24

Бренд: Febco Страницы: 12

Бренд: GameSir Страницы: 8

Бренд: Game ready Страницы: 21

Бренд: VAMP Страницы: 304

Бренд: Tactical Страницы: 8

Бренд: Lamtec Страницы: 136

Compact Comfort VAV12

Бренд: SAI HVAC Страницы: 16

Бренд: Saitek Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды