National Instruments SCXI-1530 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 60

National Instruments SCXI-1530 Скачать руководство пользователя страница 36

Chapter 2

Using the SCXI-1530/1531

SCXI-1530/1531 User Manual

2-12

www.ni.com

mode, you can use an SCXI-1180 feedthrough connector to make each of
the outputs available at the front of the chassis. This is useful for cascading
these signals to other modules for additional signal conditioning purposes.
The advantage to using parallel mode is that you are bypassing scanning
and are not limited by the settling time required by the multiplexer of the
SCXI-1530/1531 module. Using this mode, you may be able to scan the
channels more accurately and at a faster rate, depending upon which DAQ
device you connect to your module.

Using Software for Parallel Scanning

Performing SCXI-1530/1531 scanning operations in parallel mode requires
no special channel strings or function calls for setting up channel
sequencing as is required in multiplexed mode. Scanning the
SCXI-1530/1531 channels on a differentially configured DAQ device is
done as if there were no SCXI-1530/1531 module connected. The only
requirement is that you must configure the module for parallel mode in
Measurement & Automation Explorer as described in

Configuring the

SCXI-1530/1531

of Chapter 1,

Installing and Configuring

the SCXI-1530/1531

LabVIEW and Parallel Mode

In LabVIEW, the SCXI-1530/1531 configuration settings are
automatically passed from Measurement & Automation Explorer.
LabVIEW can also set the SCXI-1530/1531 configuration parameter
operating mode to parallel or multiplexed programmatically using the

Set SCXI Information

VI. In BridgeVIEW, Measure, and

ComponentWorks, set the operating mode using Measurement &
Automation Explorer as described in Chapter 1,

Installing and Configuring

the SCXI-1530/1531

After parallel mode is configured in software, you can scan the
SCXI-1530/1531 channels by entering the corresponding DAQ device
channels or a sequential SCXI channel string in the channel parameter in
the analog input application. You can also enter virtual channels.

C and Parallel Mode

When using a C-based ADE, no special steps are needed to configure the
chassis, the SCXI-1530/1531, or the DAQ device for parallel scanning.
You still have to configure the gain and filter settings by using

SCXI_Set_Gain

and

SCXI_Configure_Filter

. You should also

use the NI-DAQ

SCXI_Track_Hold_Setup

and

SCXI_Track_Hold_Control

functions to configure the

«
...
34
35
36
37
38
...
»

Содержание SCXI-1530





























































Отзывы:

Нет отзывов