manualshive.com logo in svg

National Instruments SCB-100A, Руководство пользователя, Страница: 9 / 12

Поделиться
Скачать
National Instruments SCB-100A Скачать руководство пользователя страница 9

Power Requirements

Maximum current at screw terminals

Terminals 1-48, 51-98

0.5 A

Terminals 49-50, 99-100

1 A

Caution

 

Maximum current allowed at screw terminals may be less than specified

depending on the DAQ device or module connected to the SCB-100A. Refer to the
device specifications for maximum ratings of your device or module.

Physical Characteristics

Dimensions (including feet)

14.7 cm × 14.7 cm × 3.0 cm
(5.8 in. x 5.8 in. × 1.2 in.)

Weight

670 g (1 lb 7.6 oz)

I/O connector

One 100-pin male 0.050 series shielded D-type
connector

Number of screw terminals

100, all I/O signals are available at screw
terminals

Screw-terminal wiring

Gauge

0.25 mm

2

 to 1.29 mm

2

 (30 AWG to 16 AWG)

solid or stranded wire

Wire strip length

6 mm (0.24 in.)

Temperature rating

90 °C minimum

Torque

0.5 N · m to 0.6 N · m
(4.4 in. · lb to 5.3 in. · lb)

Wires per screw terminal

One wire per screw terminal

Note

 

It may not be possible to connect wires to all screw terminals through the

opening of the enclosure when using wire larger than 1.02 mm

2

 (18 AWG).

Safety Voltages

Maximum voltage

30 V RMS, 42 V peak, 60 V DC

Caution

 

Not for use for measurements of MAINS circuits or Measurement

Categories II, III, or IV.

Environmental

Operating temperature

0 °C to 70 °C

Storage temperature

-18 °C to 82 °C

SCB-100A User Guide

  | 

© National Instruments

  | 

9

Содержание SCB-100A













Отзывы:

Нет отзывов