manualshive.com logo in svg

National Instruments SC Express PXIe-4330, Процедура калибровки

Поделиться
Скачать
National Instruments SC Express PXIe-4330 Скачать руководство пользователя страница 15

PXIe-4330/4331 Calibration Procedure

|

© National Instruments

|

15

10. If calibrating a PXIe-4331, repeat steps 2 through 9 using a sample rate of 102.4 kHz.
11. Repeat steps 1 through 10 for each channel you want to verify.

Shunt Quarter-Bridge Calibration Accuracy Verification

This section provides instructions for verifying the PXIe-4330/4331 shunt quarter-bridge 
calibration accuracy. Table 10 shows all settings for the PXIe-4330/4331. Throughout the shunt 
quarter-bridge calibration accuracy verification, use Table 26 to determine if the module is 
operating within its specified range. If the module is not operating within the specified values, 
refer to the 

Worldwide Support and Services

 section for assistance in returning the 

PXIe-4330/4331 to NI. 

Complete the following steps to test the accuracy of the module shunt quarter-bridge calibration.
1.

Configure the switch modules to connect to the channel you want to verify. Refer to Table 5 
for the specific switch column and row configuration. The connection paths are shown in 
Figure 14 in 

Appendix A: Connection Path Details

.

Note

Only one channel can be connected to the calibrator at a time.

2.

Set the calibrator output for 2-wire compensation (COMP 2-wire). This automatically 
compensates for the lead wire resistance in series with the HI and LO terminals of the 
calibrator.

3.

Set the calibrator resistance output to 120

Ω

, 350

Ω

, or 1000

Ω

, depending on the 

quarter-bridge configuration you want to verify. This must match the configuration setting 
made in step 7.

4.

Set the calibrator to operate mode (OPR).

5.

Create the DAQmx task.

6.

Create and configure an AI Bridge (V/V) channel.

7.

Configure the properties for the acquisition as described in Table 10.

Table 5.  

Shunt Quarter-Bridge Calibration Accuracy Verification

Channel

S

witch 1

0

r1->c0,r0->c1,r1->c15,r3->c16,r0->c17,r3->c18

1

r1->c0,r0->c1,r1->c20,r3->c21,r0->c22,r3->c23

2

r1->c0,r0->c1,r1->c25,r3->c26,r0->c27,r3->c28

3

r1->c0,r0->c1,r1->c30,r3->c31,r0->c32,r3->c33

4

r1->c0,r0->c1,r1->c35,r3->c36,r0->c37,r3->c38

5

r1->c0,r0->c1,r1->c40,r3->c41,r0->c42,r3->c43

6

r1->c0,r0->c1,r1->c45,r3->c46,r0->c47,r3->c48

7

r1->c0,r0->c1,r1->c50,r3->c51,r0->c52,r3->c53

Содержание SC Express PXIe-4330









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды