manualshive.com logo in svg

National Instruments SC Express PXIe-4330, Процедура калибровки

Поделиться
Скачать
National Instruments SC Express PXIe-4330 Скачать руководство пользователя страница 1

CALIBRATION PROCEDURE

PXIe-4330/4331

This document contains information about verifying and adjusting National Instruments 
PXIe-4330/4331 modules using NI-DAQmx 9.1 and later. For more information about 
calibration, visit 

ni.com/calibration

.

Contents

Software.................................................................................................................................... 2
Documentation.......................................................................................................................... 2
Calibration Interval................................................................................................................... 2
Test Equipment......................................................................................................................... 3
Test Conditions......................................................................................................................... 4
Calibration Procedure ............................................................................................................... 4

Initial Setup....................................................................................................................... 5
Connecting the Equipment ............................................................................................... 5

Install the CAL-4330 Into a Rack (Optional)........................................................... 7
Connect the Calibration and Switch Cables ............................................................. 8
Connect the DMM and Multifunction Calibrator Cables......................................... 10

Verification Procedures .................................................................................................... 11

Gain Accuracy Verification...................................................................................... 11
Input Offset Verification .......................................................................................... 14
Shunt Quarter-Bridge Calibration Accuracy Verification........................................ 15
Shunt Calibration Resistance Accuracy Verification ............................................... 17
Excitation Voltage Verification................................................................................ 18

Gain and Offset Adjustment Procedure............................................................................ 20

Test Limits................................................................................................................................ 24

Gain Accuracy Test Limits............................................................................................... 25
Input Offset Test Limits ................................................................................................... 31
Shunt Quarter-Bridge Calibration Test Limits ................................................................. 32
Shunt Calibration Resistance Test Limits ........................................................................ 32
Excitation Voltage Test Limits......................................................................................... 33

Appendix A: Connection Path Details...................................................................................... 34
Worldwide Support and Services ............................................................................................. 40

Содержание SC Express PXIe-4330









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды