background image

16

|

ni.com

|

NI PS-12/13 Power Supply User Manual and Specifications

Electromagnetic Compatibility

This product meets the requirements of the following EMC standards for electrical equipment 
for measurement, control, and laboratory use: 

EN61000-4-2, EN61000-4-3, EN61000-4-4, EN61000-4-5, EN61000-4-6, EN61000-4-8, 
EN61000-4-11

FCC-Class B

EN55011/EN55022-B

CISPR22 Class B

Note

For EMC declarations and certifications, refer to the 

Online Product 

Certification

 section. 

CE Compliance

This product meets the essential requirements of applicable European Directives, as follows:

2006/95/EC; Low-Voltage Directive (safety) 

2004/108/EC; Electromagnetic Compatibility Directive (EMC)

Online Product Certification

To obtain product certifications and the Declaration of Conformity (DoC) for this product, visit 

ni.com/certification

, search by model number or product line, and click the appropriate 

link in the Certification column.

Environmental Management

NI is committed to designing and manufacturing products in an environmentally responsible 
manner. NI recognizes that eliminating certain hazardous substances from our products is 
beneficial to the environment and to NI customers.

For additional environmental information, refer to the 

Minimize Our Environmental Impact

 web 

page at 

ni.com/environment

. This page contains the environmental regulations and 

directives with which NI complies, as well as other environmental information not included in 
this document.

Waste Electrical and Electronic Equipment (WEEE)

EU Customers

At the end of the product life cycle, all products 

must

 be sent to 

a WEEE recycling center. For more information about WEEE recycling centers, 
National Instruments WEEE initiatives, and compliance with WEEE Directive 
2002/96/EC on Waste and Electronic Equipment, visit 

ni.com/environment/

weee

.

⬉ᄤֵᙃѻક∵ᶧ᥻ࠊㅵ⧚ࡲ⊩ ˄Ё೑

RoHS

˅

Ё೑ᅶ᠋

National Instruments

ヺড়Ё೑⬉ᄤֵᙃѻકЁ䰤ࠊՓ⫼ᶤѯ᳝ᆇ⠽䋼ᣛҸ

 (RoH

݇Ѣ

National Instruments

Ё೑

RoHS

ড়㾘ᗻֵᙃˈ䇋ⱏᔩ

ni.com/environment/rohs_c

(For information about China RoHS compliance, go to 

ni.com/environment/rohs_

Содержание NI PS-12


















Отзывы: