National Instruments NI-9146 Скачать руководство пользователя

Страница: 24 / 29

for measurements of voltages from specially protected secondary circuits. Such

voltage measurements include signal levels, special equipment, limited-energy

parts of equipment, circuits powered by regulated low-voltage sources, and

electronics.

Caution

Do not connect the NI 9146 to signals or use for measurements

within Measurement Categories II, III, or IV.

Note

Measurement Categories CAT I and CAT O are equivalent. These test

and measurement circuits are not intended for direct connection to the

MAINS building installations of Measurement Categories CAT II, CAT III, or

CAT IV.

Safety and Hazardous Locations Standards

This product is designed to meet the requirements of the following electrical

equipment safety standards for measurement, control, and laboratory use:

■

IEC 61010-1, EN 61010-1

■

UL 61010-1, CSA 61010-1

■

EN 60079-0:2012, EN 60079-15:2010

■

IEC 60079-0: Ed 6, IEC 60079-15; Ed 4

■

UL 60079-0; Ed 5, UL 60079-15; Ed 3

■

CSA 60079-0:2011, CSA 60079-15:2012

Note

For UL and other safety certifications, refer to the product label or

the

Online Product Certification

section.

Electromagnetic Compatibility

This product meets the requirements of the following EMC standards for sensitive

electrical equipment for measurement, control, and laboratory use:

■

EN 61326-2-1 (IEC 61326-2-1): Class A emissions; Industrial immunity

■

EN 55011 (CISPR 11): Group 1, Class A emissions

ni.com

NI-9146 Safety, Environmental, and Regulatory Information

Содержание NI-9146






























Результаты поиска

Содержание NI-9146

Отзывы:

Похожие инструкции для NI-9146

Бренды по названию

Популярные бренды

National Instruments NI-9146, Информация о безопасности, охране окружающей среды и нормативных требованиях

Результаты поиска

Содержание NI-9146

Отзывы:

Похожие инструкции для NI-9146

Бренды по названию

Популярные бренды