National Instruments NI-9146 Скачать руководство пользователя

Страница: 25 / 29

■

AS/NZS CISPR 11: Group 1, Class A emissions

■

FCC 47 CFR Part 15B: Class A emissions

■

ICES-001: Class A emissions

Note

In the United States (per FCC 47 CFR), Class A equipment is

intended for use in commercial, light-industrial, and heavy-industrial

locations. In Europe, Canada, Australia and New Zealand (per CISPR 11)

Class A equipment is intended for use only in heavy-industrial locations.

Note

Group 1 equipment (per CISPR 11) is any industrial, scientific, or

medical equipment that does not intentionally generate radio frequency

energy for the treatment of material or inspection/analysis purposes.

Note

For EMC declarations and certifications, and additional

information, refer to the

Online Product Certification

section.

CE Compliance

This product meets the essential requirements of applicable European Directives, as

follows:

■

2014/35/EU; Low-Voltage Directive (safety)

■

2014/30/EU; Electromagnetic Compatibility Directive (EMC)

■

94/9/EC; Potentially Explosive Atmospheres (ATEX)

Online Product Certification

Refer to the product Declaration of Conformity (DoC) for additional regulatory

compliance information. To obtain product certifications and the DoC for this

product, visit

ni.com/certification

, search by model number or product line, and

click the appropriate link in the Certification column.

© National Instruments

NI-9146 Safety, Environmental, and Regulatory Information

Содержание NI-9146






























Результаты поиска

Содержание NI-9146

Отзывы:

Похожие инструкции для NI-9146

Бренды по названию

Популярные бренды

National Instruments NI-9146, Информация о безопасности, охране окружающей среды и нормативных требованиях

Результаты поиска

Содержание NI-9146

Отзывы:

Похожие инструкции для NI-9146

Бренды по названию

Популярные бренды