background image

NI PCIe-8231 Quick Start Guide

2

ni.com

not

 use it until service-trained personnel can check its safety. If necessary, 

return the device to National Instruments for repair.

Keep away from live circuits. Do 

not

 remove equipment covers or shields 

unless you are trained to do so. If signal wires are connected to the device, 
hazardous voltages can exist even when the equipment is turned off. To 
avoid a shock hazard, do 

not

 perform procedures involving cover or shield 

removal unless you are qualified to do so. Disconnect all field power prior 
to removing covers or shields.

If the device is rated for use with hazardous voltages (>30 V

rms

, 42.4 V

pk

or 60 V

dc

), it may require a safety earth-ground connection wire. Refer to 

the device specifications for maximum voltage ratings.

Because of the danger of introducing additional hazards, do 

not

 install 

unauthorized parts or modify the device. Use the device only with the 
chassis, modules, accessories, and cables specified in the installation 
instructions. All covers and filler panels 

must

 be installed while operating 

the device.

Do 

not

 operate the device in an explosive atmosphere or where flammable 

gases or fumes may be present. Operate the device only at or below the 
pollution degree stated in the specifications. Pollution consists of any 
foreign matter—solid, liquid, or gas—that may reduce dielectric strength 
or surface resistivity. The following is a description of pollution degrees.

Pollution Degree 1—No pollution or only dry, nonconductive 
pollution occurs. The pollution has no effect.

Pollution Degree 2—Normally only nonconductive pollution occurs. 
Occasionally, nonconductive pollution becomes conductive because of 
condensation.

Pollution Degree 3—Conductive pollution or dry, nonconductive 
pollution occurs. Nonconductive pollution becomes conductive 
because of condensation.

Clean the device and accessories by brushing off light dust with a soft, 
nonmetallic brush. Remove other contaminants with a stiff, nonmetallic 
brush. The unit 

must

 be completely dry and free from contaminants before 

returning it to service.

You

 must

 insulate signal connections for the maximum voltage for which 

the device is rated. Do 

not

 exceed the maximum ratings for the device. 

Remove power from signal lines before connection to or disconnection 
from the device. 

Содержание Gigabit Ethernet (GigE) Interface Device NI...












Отзывы: