National Instruments FlexDMM PXI-4070 Скачать руководство пользователя страница 53

Страница: 53 / 68

National Instruments Corporation

NI 4070/4072 Calibration Procedure

You have completed adjusting the AC voltage modes of the NI 4070/4072.
Select one of the following options:

•

If you are performing additional adjustments, refer to the following
sections, as applicable:

–

Adjusting Current Modes

–

Adjusting Capacitance and Inductance (NI 4072 Only)

Caution

For the NI 4072, adjusting the capacitance and inductance is required. Skipping

this step causes an incorrect adjustment of the device.

•

If you are

not

performing additional adjustments, refer to one of the

following sections:

–

Verification Procedures

—to verify your new calibration

coefficients before saving them to the EEPROM

–

Completing the Adjustment Procedures

—if you do

not

want to

verify the adjustments you have just made

Adjusting Current Modes

If you do not use the current modes (DC and AC), or the accuracy is
insignificant for your application, you can skip this section and select one
of the following options:

•

If you skip this section and you are calibrating an NI 4072, go to the

Adjusting Capacitance and Inductance (NI 4072 Only)

section.

•

If you skip this section and you want to verify the new calibration
coefficients before saving them to the EEPROM, repeat the

Verification Procedures

section (except for

Initial Setup

•

If you skip this section and you do not want to verify the new
calibration coefficients, go to the

Completing the Adjustment

Procedures

section.

To adjust the current modes of the NI 4070/4072, complete the following
steps:

Reset the calibrator.

Fasten the connectors on one end of the Fluke 5440 cable to the
NI 4070/4072

HI SENSE

and

banana plug connectors, and fasten

the connectors on the other end of the cable to the

and

calibrator

binding posts. Figure 4 shows the correct connections. Table 11 lists
the cable connections.

Call

niDMM_ConfigureMeasurement

with the following

parameters:

•

Function

NIDMM_VAL_DC_CURRENT

•

Range

0.02

Содержание FlexDMM PXI-4070





































































Результаты поиска

Содержание FlexDMM PXI-4070

Отзывы:

Похожие инструкции для FlexDMM PXI-4070

Бренды по названию

Популярные бренды

National Instruments FlexDMM PXI-4070, Процедура калибровки

Результаты поиска

Содержание FlexDMM PXI-4070

Отзывы:

Похожие инструкции для FlexDMM PXI-4070

Бренды по названию

Популярные бренды