National Instruments FlexDMM PXI-4070 Скачать руководство пользователя страница 29

Страница: 29 / 68

National Instruments Corporation

NI 4070/4072 Calibration Procedure

33. Call

niDMM_ConfigureMeasurement

with the following

parameters:

•

Function

NIDMM_VAL_2_WIRE_RES

•

Range

10e3

•

Resolution

0.01

34. Call

niDMM_Read

. This allows the calibrator to properly settle for a

10 k

compensated measurement at the NI 4070/4072.

35. Call

niDMM_Read

. Verify that the result falls between the tolerances

listed in Table 20.

36. Output 1 k

on the calibrator with 2-wire compensation and external

sense turned on.

37. Call

niDMM_ConfigureMeasurement

with the following

parameters:

•

Function

NIDMM_VAL_2_WIRE_RES

•

Range

1e3

•

Resolution

1e-3

38. Call

niDMM_Read

. Verify that the result falls between the tolerances

listed in Table 20.

39. Output 100

on the calibrator with 2-wire compensation and external

sense turned on.

40. Call

niDMM_ConfigureMeasurement

with the following

parameters:

•

Function

NIDMM_VAL_2_WIRE_RES

•

Range

100

•

Resolution

100e-6

41. Call

niDMM_Read

. Verify that the result falls between the tolerances

listed in Table 20.

You have completed verifying the 2-wire resistance of the NI 4070/4072.
Select one of the following options:

•

If you want to continue verifying other modes, go to the

Verifying DC

Current

section.

•

If you do

not

want to verify other modes

and

you are performing a

post-adjustment

verification, go to the

Completing the Adjustment

Procedures

section.

•

If you do

not

want to verify any additional modes

and

you are

performing a

pre-adjustment

verification, call

niDMM_close

to close

the session.

Содержание FlexDMM PXI-4070





































































Результаты поиска

Содержание FlexDMM PXI-4070

Отзывы:

Похожие инструкции для FlexDMM PXI-4070

Бренды по названию

Популярные бренды

National Instruments FlexDMM PXI-4070, Процедура калибровки

Результаты поиска

Содержание FlexDMM PXI-4070

Отзывы:

Похожие инструкции для FlexDMM PXI-4070

Бренды по названию

Популярные бренды