manualshive.com logo in svg

National Flooring Equipment PANTHER 8274, Инструкция по эксплуатации

Поделиться
Скачать
National Flooring Equipment PANTHER 8274 Скачать руководство пользователя страница 2

Page 2

8274/9274 TABLE OF CONTENTS

Table of Contents ..........................................................................................................2

Rules for Safe Operation ..........................................................................................3-7

A. Grounding ......................................................................................................6
B. Extension Cords ............................................................................................7

Safety Instructions ........................................................................................................8

Transportation ..............................................................................................................9

A.  Load and Unloading........................................................................................9

Features/Specifications ..............................................................................................10

Procedure ..............................................................................................................11-23

A. Handle 

Assembly ..........................................................................................11

B. Vacuum Port ................................................................................................12
C. Weights ........................................................................................................12
D.  Rubber Dust Guard ......................................................................................13
E. Belt ..........................................................................................................14-16
F.  Idler Bearing Replacement ..........................................................................17
G. Pulley Replacement ......................................................................................17
H.  Satellite Shaft Replacement ........................................................................18
I.  Satellite Bearing Replacement ....................................................................18
J.  Removing Top Gear Plate ............................................................................19
K.  Light In Cord Plug ........................................................................................19
L.  Machine Start Up ..........................................................................................20
M.  Controller Fault/Circuit Overload .................................................................21
N. Controller Codes ..........................................................................................22

i. Controller Default Codes........................................................................22

ii. Controller Error Codes ..........................................................................22

O. Troubleshooting..........................................................................................22.1
P.   Power Cord ..................................................................................................23
Q. Power Source Voltage ..................................................................................23

Accessory Set-Up ..................................................................................................24-25

Maintenance ..........................................................................................................26-27

A. Maintaining Tools ..........................................................................................26
B. Cleaning........................................................................................................27
C. Repairs..........................................................................................................27

Complete Parts List ..............................................................................................28-31

A. 8274 ........................................................................................................28-29
B. 9274 ........................................................................................................30-31

Part Numbers & Diagrams ....................................................................................32-36

Labels ........................................................................................................................37

Magnetic Tooling ....................................................................................................38-40

Traditional Tooling..................................................................................................41-43

Tooling Packages ..................................................................................................44-46

Guarantee ..................................................................................................................46

Return Sheet ..............................................................................................................47

Содержание PANTHER 8274


















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды