English
18
Commissioning
Inserting and removing battery
Insert the battery (1) fully into the compartment at the bottom
of drill screwdriver (hereinafter referred to as „device“). Check the
proper fitting of the battery by pulling it.
To remove the battery (1), push both clips (2) and pull the battery
out.
Checking battery status
The device is equipped with battery status indicator (3).
With the battery inserted into the device, push the button
switch (3) to turn on the status indicator (9) signalizing the follow-
ing states (based on current capacity):
• If the battery is fully charged, all three LED indicator lights are
on – red, yellow, green.
• If the battery is half charged, two LED indicator lights are on –
red, yellow.
• If the battery is nearly flat (<20 %), only red LED indicator light
is on.
Switching on
Push the button (3) gradually to adjust the speed. Pushing the
button (3) will automatically turn on the LED (7) designed for the
illumination of working area in front of the chuck tool.
Switching off
Release the switch (3). After switching off, rundown of the chuck
spindle is reduced thanks to electronic rundown brake.
Lower speed is suitable for wood screw/screw guidance into the
material. Higher speed is suitable for wood screw/screw setting
into the material or for drilling.
Attention! Prolonged use of variable speed of rotation
is not recommended. It could damage the switch.
Changed direction of rotation
Direction of rotation is changed by the change over switch of the
sense of rotation (4):
• By pushing from the right to the left – right run.
• By pushing from the left to the right – left run.
• Push button in the interposition – protection from uninten-
tional switching.
Attention!
If you wish to change position of the change over switch, check at
first that the operating push button is released.
Note:
During first use of the device and during the first change of the
sense of rotation a loud click can be heard. It is a normal phenome-
non which cannot be considered any problem.
Speed changing
Speed changing is carried out by the sliding switch (5).
1. low speed:
move the switch towards the chuck
- the block letter “
L
” (LOW) will appear
2. high speed:
move the switch from the chuck
- the block letter “
H
” (HIGH) will appear
Torque setting
The necessary torque can be set by swiveling the adjusting ring (6)
towards the relevant symbol.
Screwing
Symbol
1
= min. torque
Symbol
18
= max. torque for screwing
Drilling
Symbol
= max. torque
Tool clamping and releasing
By swiveling the clamping chuck sleeve (8), you open and close
the clamping jaws, which the working tool (bit, bit holder, etc.) is
inserted into. The devices are equipped by automatic spindle arrest
(locking) facilitating tool replacement, by using one hand only in
the requested direction.
Maintenance and service
Instructions for device cleaning
Start the motor and blow impurities and dust out of the vent holes
of the device. Use protective goggles for this operation. Clean the
external plastic parts by a wet rag and mild detergent. Though
these parts are made of the materials resistant to solvents,
NEVER
use any solvent.
Instructions for cleaning the charger
Attention! Risk of electric shock. Prior to start handling
the charger, disconnect the line plug from the socket!
Impurities and dust can be removed from external charg-
er surfaces by a rag or a non-metal brush. Use neither water nor
detergents.
Attention! With respect to protection from el. shock
and preservation of the class of protection, all mainte-
nance and service operations requesting jig saw case
removal must be performed by the authorized service centre
only!
The current list of authorized service centres can be found at our
website
www.narex.cz
, section
“Service centres”
.
Accessories
The accessories recommended for use with this device are availa-
ble commercially in the shops with hand el. tools.
Storage
Packed appliance may be stored in dry, unheated storage place
with temperature not lower than -5 °C.
Unpacked appliance should be stored only in dry storage place
with temperature not lower than +5 °C with exclusion of all sudden
temperature changes.
Environmental protection
Power tools, accessories and packaging should be sorted for envi-
ronmental-friendly recy.
Only for EU countries:
Do not dispose of power tools into household waste!
According to the European Directive 2002/96/EC on waste electri-
cal and electronic equipment and its incorporation into national
law, power tools that are no longer suitable for must be separately
collected and sent for recovery in an environmental-friendly man-
ner.
Warranty
Our equipment is under warranty for at least 12 months with re-
gard to material or production faults in accordance with national
legislation. In the EU countries, the warranty period for exclusively
private use is 24 months (an invoice or delivery note is required as
proof of purchase).
Damage resulting from, in particular, normal wear and tear, over-
loading, improper handling, or caused by the user or other dam-
age caused by not following the operating instructions, or any
fault acknowledged at the time of purchase, is not covered by the
warranty.
Complaints will only be acknowledged if the equipment has not
been dismantled before being sent back to the suppliers or to an
authorised NAREX customer support workshop. Store the operat-
ing instructions, safety notes, spare parts list and proof of purchase
in a safe place. In addition, the manufacturer’s current warranty
conditions apply.
Note
Due to continuous research and development work, we reserve
the right to make changes to the technical content of this docu-
mentation.
