background image

30

W415-0153 / B / 06.10.10

5.2.1

  Place the back log into the 

fi

 rebox, pushing it as close 

to the 

fi

 rebox wall as possible and centered onto the 

log support pan.

5.2.2

  Place the front log on the ember screen lining up the 

studs with the holes on the bottom of the log.

 

NOTE: The ember screen is adjustable front to 
back. To avoid fl ame impingement on propane 
move the ember screen to the back most position. 
Loosen the two screws that secure the ember 
screen, move the screen back and retighten the 
screws. 

 

The glowing ember screen is positioned in the 

fl

 ame to maximize the glow effect. Even though it is 

constructed of the highest quality material, it is subject 
to deterioration over time and consequently will need to 
be replaced.  Replacement of the ember screen is not

             covered under the warranty policy

5.2.3

  Set the two cross-over logs into the pockets provided 

on both the front and rear logs as shown.

PHAZER

TM

 logs, glowing embers and charcoal embers exclusive to Wolf Steel Ltd. 

fi

 replaces, glow when 

exposed to direct 

fl

 ame and provide a unique and realistic glowing effect that is different in every installation. 

Use only certi

fi

 ed PHAZER

TM

 logs, glowing embers and charcoal embers available from your local authorized 

dealer / distributor. 

Log colours may vary. During the initial use of the appliance, the colours will become more uniform as colour 
pigments burn in during the heat activated curing process.

5.2 LOG 

PLACEMENT

!

WARNING

FAILURE TO POSITION THE LOGS IN ACCORDANCE WITH THESE DIAGRAMS OR FAILURE TO USE 

ONLY LOGS SPECIFICALLY APPROVED WITH THIS APPLIANCE MAY RESULT IN PROPERTY 

DAMAGE OR PERSONAL INJURY.

LOGS MUST BE PLACED IN THEIR EXACT LOCATION IN THE APPLIANCE. DO NOT MODIFY THE 

PROPER LOG POSITIONS, SINCE APPLIANCE MAY NOT FUNCTION PROPERLY AND DELAYED 

IGNITION MAY OCCUR.

THE LOGS ARE FRAGILE AND SHOULD BE HANDLED WITH CARE. 

76.1A

1

2

3

4

Содержание Haliburton GDS28P

















































Отзывы: