Napoleon GSS48ST Скачать руководство пользователя

Страница: 24 / 68

www.napoleongrills.com

LED Lights

: Your appliance has been equipped with a LED (light) strip which is programmed with three

colour modes. Plug the LED power supply into a GFI protected electrical outlet.

Turn on the light switch located under the access panel and toggle the switch off and on to cycle through

to desired Mode.

Mode 1

- Simulated White.

Mode 2

- Continuous 2 colour shift. Takes 8-10 seconds to smoothly ramp up one colour to 100%, as the

other fades off from 100% to 0. Continually shifts in colour (17 seconds per colour, up and back down.)

Mode 3

- Freeze Mode Colour stops the colour shift on whichever colour it was on in Mode 2 at the time it

was turned off, does not continue to shift.

NOTE!

Switch off for 10 seconds to reset to beginning colour mode.

WARNING!

Glass embers may have sharp edges, wear safety glasses and gloves when handling.

Do not change or substitute the glass ember material provided with this appliance. If replacing, use

only replacement glass embers available from your local authorized dealer / distributor.

WARNING!

To avoid the possibility of burns, maintenance should be done only when the

appliance is cool. Avoid unprotected contact with hot surfaces. Ensure burner is turned off. Turn gas off

at source and disconnect the appliance before servicing. Clean the appliance in an area where cleaning

solutions will not harm decks, lawns, or patios. Do not use flammable, corrosive or abrasive cleaners.

Note

: Stainless steel tends to oxidize or stain in the presence of chlorides and sulfides, particularly in

coastal areas and other harsh environments, such as the warm, highly humid atmosphere around pools

and hot tubs. These stains could be perceived as rust, but can be easily removed or prevented. To provide

stain prevention and removal, wash all stainless steel surfaces every 3-4 weeks or as often as required

with fresh water and/or stainless steel cleaner.

Control Panel

: The control panel text is printed directly on the stainless steel and with proper maintenance

will remain dark and legible. To clean the panel, use only warm soapy water or stainless steel cleaner

available from your Napoleon dealer. Never apply abrasive cleaners on any stainless surfaces, especially

the printed portion of the control panel or the printing will gradually rub off.

Maintenance / Cleaning Instructions

WARNING!

Hose: Check for abrasions, melting, cuts, and cracks in the hose. If any of these

conditions exist, do not use the appliance. Have the part replaced by your Napoleon dealer or qualified

gas installer.

Cleaning Inside The Appliance

: While washing your appliance, be sure to keep the area around the

burner and pilot assembly dry at all times.

WARNING!

If the gas control is exposed to water in any way, DO NOT try to use the appliance.

The gas control must be replaced.

AC Connector

Transformer

120 vAC

12 vAC

Threaded

Power

Connector

FLAG

CONNECTORS

Digital Control Unit for

LED Colour switching

MD6

Connector

MD6

Connector

Strip Light

Содержание GSS48ST





































































Результаты поиска

Содержание GSS48ST

Отзывы:

Похожие инструкции для GSS48ST

Бренды по названию

Популярные бренды

Napoleon GSS48ST, Руководство пользователя

Результаты поиска

Содержание GSS48ST

Отзывы:

Похожие инструкции для GSS48ST

Бренды по названию

Популярные бренды