background image

13

Wiring for Arm / Disarm

Program a zone on the control panel for “Keyswitch Arm”

• 

When [

ON/OFF

] is pressed, the Arm/Disarm relay will

change state (from normally closed to normally open) for 2
seconds and then restore, causing the control panel to arm
or disarm.

Zone programmed for

Keyswitch Arm

Typical Keyswitch wiring

for a zone using

End of Line resistors

EOLR

COM

8

N/O

N/C

9

10

Typical Keyswitch wiring

for a “zone doubled” zone

Zone programmed for

Keyswitch Arm

COM

8

N/O

N/C

9

10

ZDR*

Wiring for Panic

Program a zone on the control panel as a 24 Hour Panic
Zone.

• 

When  [PANIC]  is pressed, the Panic relay will change
state (from normally closed to normally open) for 2
seconds and then restore, causing an alarm on the the
control panel Panic Zone.

Zone programmed for

24 hour panic

Typical Panic wiring

for a zone using

End of Line resistors

Zone programmed for

24 hour panic

Typical Panic wiring

for a “zone doubled” zone

EOLR

COM

11

N/O

N/C

12

13

COM

11

N/O

N/C

12

13

ZDR

 STEP 1 

 -   WIRING FOR ARM / DISARM AND PANIC

Universal operation requires the use of control panel zones to provide Arm / Disarm and Panic operation. One zone must be
programmed as a keyswitch arm zone which will process a 2 second violation as an Arm / Disarm command. The other zone must
be programmed as a 24 hour panic zone, which will process a 2 second violation as a panic alarm. The wiring instructions below
include wiring schemes for control panels which support zone doubling, such as the NAPCO Express 

series.

EOLR PANEL

ZONE DOUBLED PANEL

EOLR PANEL

ZONE DOUBLED PANEL

* ZDR = Zone Doubling Resistor

* ZDR = Zone Doubling Resistor

 Universal Operation

Содержание 2WAY-UNIVKF





















Отзывы: