manualshive.com logo in svg

NANOTEC SMCI36, Техническое руководство

Поделиться
Скачать
NANOTEC SMCI36 Скачать руководство пользователя страница 3

  

Technical 

Manual

 

  

SMCI36

 

About this manual

 

About this manual 

Target group 

This technical manual is intended for designers and developers who lack extensive 
experience with stepper motor technology but who need to commission a Nanotec

®

 

motor. 

Important information 

This technical manual must be carefully read before installing and commissioning the 
controller. 

In the interests of its customers and to improve the function of this product, Nanotec

®

 

reserves the right to make technical alterations and further develop hardware and 
software without prior notice.  

This manual was created with due care. It is exclusively intended as a technical 
description of the product and as commissioning instructions. The warranty is 
exclusively for repair or replacement of defective equipment, according to our general 
terms and conditions; liability for subsequent damage or errors is excluded. Applicable 
standards and regulations must be complied with during installation of the device. 

For criticisms, proposals and suggestions for improvement, please contact the above 
address or send an email to: [email protected] 

Additional manuals 

Please also note the following manuals from Nanotec: 
 

NanoPro 
User Manual 

 

Configuration of controllers with the 
NanoPro software 

 

NanoCAN User Manual 

Configuration of the CAN 
communication for CANopen-
capable controllers with the 
NanoCAN software 

 

Nanotec CANopen 
reference 

Comprehensive documentation of 
the CANopen functions 

 

Programming manual 

 

Controller programming  

•

 Command 

Reference 

•

 NanoJ 

•

 COM 

port 

 

The manuals are available for downloading at www.nanotec.de. 

Issue: V 1.0 

 

3

 

Содержание SMCI36





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды