manualshive.com logo in svg

NANOTEC SMCI36, Техническое руководство

Поделиться
Скачать
NANOTEC SMCI36 Скачать руководство пользователя страница 17

  

Technical 

Manual

 

  

SMCI36

 

Connections and wiring

 

3.4.4  Power supply connection 

Permissible operating voltage 

The permissible operating voltage for the SMCI36 lies b12 and +72 V DC; it 
must not exceed 75 V or fall below 10 V. 

A charging capacitor with minimum 4700 µF (10000 µF) must be provided for the 
operating voltage to prevent exceeding the permissible operating voltage (e.g. during 
braking). 

 

 

 

 

Danger of electrical overvoltage 

Connect a charging capacitor with minimum 4700 µF! 
Use charging capacitors Z-K4700 from Nanotec to a maximum operating voltage of 
50 V only! 
Connect a capacitor with 10000 µF for motors with flange size 86x86 (series ST8918) 
or greater! 
An operating voltage > 75 V will destroy the output stage! 
Accidentally swapping the connections will destroy the output stage. See the data 
sheet of the connected stepper motor. 
Never disconnect the motor while operating voltage is applied! 

Never

 hot-unplug lines. 

 

 

Connection diagram 

 

Note:

 

Overall connection diagram, see Section 2 "Connecting and commissioning". 

Accessories 

Appropriate power packs and charging capacitors are available as accessories: 

Designation Order 

identifier 

Power pack 

NTS-xxV-yA 
(xx=voltage, y=current) 
Information on the selection of the required 
power supply unit can be found in our FAQ on 
www.nanotec.de. 

Charging capacitor 

Z-K4700 (to max. 50 V) or Z-K10000 

Note:

 

Further information about accessories can be found on the Nanotec website: 
www.nanotec.de 

 

 

 

Issue: V 1.0 

 

17

 

Содержание SMCI36





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды