Nanni T4.155 seriers Скачать руководство пользователя страница 34

Страница: 34 / 191

60300140

(

indice A

)

4 CYLINDERS WORKSHOP MANUAL 34/191

COMPRESSION MEASUREMENT

CHECKING THE COMPRESSION

ADVICE:

Measure cylinder compression pressure when the engine efficiency is low, oil
consumption excessive or fuel consumption uneconomical.

WARM THE ENGINE, THEN STOP IT

Allow the engine to heat up to its normal operating temperature.

2) DISCONNECT THE INJECTION PUMP WIRING COUPLING UNIT

(POWER SUPPLY CUTOFF CONTROL SOLENOID

3) REMOVE THE INJECTORS

4) MEASURE THE COMPRESSION PRESSURE OF EACH CYLINDER

a) Install the accessory on the injector port.

b) Connect the compression meter to the accessory.

c) Measure the compression pressure while turning the engine over with the

starter.

ADVICE:

A fully charge battery must always be used in order to be sure that the engine
is rotated at least 250 rpm.

d) Repeat operations a. to c. on each cylinder.

REMARK: These measurements must be made in the shortest
possible period of time.

Содержание T4.155 seriers
































































































































































































Результаты поиска

Содержание T4.155 seriers

Отзывы:

Бренды по названию

Популярные бренды

Nanni T4.155 seriers, Руководство по ремонту

Результаты поиска

Содержание T4.155 seriers

Отзывы:

Бренды по названию

Популярные бренды