Nanni T4.155 seriers Скачать руководство пользователя страница 151

Страница: 151 / 191

60300140

(

indice A

)

4 CYLINDERS WORKSHOP MANUAL 151/191

e. Reinstall the distribution casing.

f. Make the mark made on the driven pinion of No.1 balancing

shaft correspond with mark "2".

g. Make the mark made on the oil pump drive pinion coincide

with the mark made on the timing casing.

h. Reinstall the eight assembly bolts and the coupling bolt.

Recommended tightening torque:
13 N.m (130 kgf.cm) for the assembly bolt
Recommended tightening torque:
16 N.m (160 kgf.cm) for the coupling bolt

Reinstall the two attachment nuts securing the injection

pump to the timing casing.

Recommended tightening torque: 21 N.m (210 kgf.cm

ii.

Verify the timing alignment on the injection pump (or

the alignment marks) by inclining the injection pump.

PUT SOME OIL IN THE OIL PUMP

a. Remove the tapered threaded plug.

b. Pour approximately 20 cm

of engine oil in the oil pump.

Содержание T4.155 seriers
































































































































































































Результаты поиска

Содержание T4.155 seriers

Отзывы:

Бренды по названию

Популярные бренды

Nanni T4.155 seriers, Руководство по ремонту

Результаты поиска

Содержание T4.155 seriers

Отзывы:

Бренды по названию

Популярные бренды