Nanni T4.155 seriers Скачать руководство пользователя страница 191

Страница: 191 / 191

60300140

(

indice A

)

4 CYLINDERS WORKSHOP MANUAL 191/191

POST-ASSEMBLY

1. REINSTALL THE PLUG
2. REINSTALL THE MOTOR SUSPENSION

ATTACHMENT PLATE

3. REINSTALL THE WATER TEMPERATURE SENSOR
4. REINSTALL THE THERMOSTAT AND THE WATER

INTAKE PIPES

5. REINSTALL THE OIL RADIATORS
6. REINSTALL THE ENGINE LOWER CASING AND

THE TIMING GEAR CASING (OIL PUMP)

7.  REINSTALL THE INJECTION PUMP
8.  REINSTALL THE TIMING GEARS
9.  REINSTALL THE WATER PUMP
10. REINSTALL THE ALTERNATOR AND THE

ALTERNATOR ATTACHMENT PLATES

11. REINSTALL THE CYLINDER HEAD
12. REINSTALL THE TIMING BELT AND THE TIMING

PULLEYS

13. REMOVE THE COMPLETE ENGINE FROM THE

ENGINE TEST BENCH

14. REINSTALL THE REAR CLOSING PLATE

Reinstall the rear closing plate with its assembly bolt.

Recommended tightening torque: 8 N.m (85 kgf.cm)

15. REINSTALL THE ENGINE FLY WHEEL

a. Coat the threading of the cylinder head bolts over two or three

threads with the sealant.

b. Reinstall the fly wheel on the crankshaft.

c. Reinstall and evenly tighten the assembly bolts to the

recommended tightening torque in several stages and in the
order indicated in the illustration.

Recommended tightening torque:
145 N.m (1,480 kgf.cm)

16. REINSTALL THE CLUTCH CLOSING PLATE AND

THE DISK

Содержание T4.155 seriers
































































































































































































Результаты поиска

Содержание T4.155 seriers

Отзывы:

Бренды по названию

Популярные бренды

Nanni T4.155 seriers, Руководство по ремонту

Результаты поиска

Содержание T4.155 seriers

Отзывы:

Бренды по названию

Популярные бренды