background image

2. Precautions

(1) For indoor use only ­ do not install in the following location

① Outdoors

② Places exposed to direct sunlight, places with high humidity, dusty places, places with

leaks / water leaks, heating appliances, extremely cold places

③ Places that hinder disaster prevention such as emergency exits and places where

firefighting equipment is installed.

④ Unstable places and floors with vibration

(2)

(1) The machine can be used in the range of AC 90v to  AC 11OV, but please use it near

AC 1OOV as much as possible. Also, be sure to connect the power plug with a dedicated

outlet.

(2)

When

 

unplugging

 

the

 

power

 

cord,

 

be

 

sure

 

to

 

hold

 

the

 

plug

 

without

 

pulling

 

on

the

 

cord.

(3)

Be sure to turn off the power when replacing parts or connecting / disconnecting

the connector.

(4)

Since the repair of the game PC board will be done by the manufacturer, never

check the continuity with a tester or the like. The internal voltage of the tester can

destroy integrated circuits on the game PCB.

- 3 -

In the case of an outlet with an earth, you can do the earth just by inserting the plug. 

If it is not an earth 1 inch outlet, insert the included conversion plug and then connect 

it to the outlet. At that time, be sure to connect the earth wire to the earth terminal of 

this unit and make a ground connection.

2 - 2  Handling Precautions (Other)

2 - 1  Environmental Precautions (Other)

Содержание EXCELEENA























Отзывы: