background image

3

BASIC PACKAGE

2.

When opening the package, check if it includes all items listed in " Table. 1 Packing List Contents ".
In the event of any shortage, please contact either NAKANISHI (see the " 4. CONTACT US " section) or your local 
dealer. 

Table. 1 Packing List Contents 

* The collet, collet nut and air hese are attached to the spindle.

WARRANTY

3.

We provide a limited warranty for our products. We will repair or replace the products if the cause of failure is due to 
the following manufactures defects. Please contact us or your local distributor for details.

Defect in manufacturing.

Any shortage of components in the package.

Where damaged components are found when initially opening the package.
(This shall not apply if the damage was caused by the negligence of a customer.)

Brushless Motor Spindle

・・

1pc.

Collet 

ȭ

3.0mm (CHK - 3.0) or 

ȭ

3.175mm 

(CHK - 3.175) 

・・

1pc.*

(For U.S. market

ȭ

3.175mm 

(CHK - 3.175))

Collet Nut (K - 265)

・・

1pc.*

Air Hose (0.3m)

・・

1pc.*

Wrench (12 x 14)

・・

2pcs.

12

14

Grease Nipple

・・

1pc.

Grease Dispenser

・・

1pc.

Inspection Card

・・

1pc.

᳨ᰝᡂ⦼⾲

Inspection Card

Operation Manual

・・

1set

ྲྀᢅㄝ᫂᭩

OPERATION MANUAL

Содержание EMA - 3020K













Отзывы: