32
DISPLAY SETUP
TV SYSTEM
Select between NTSC and PAL systems. Select NTSC (North American) or PAL (European) TV System in
order to view the OSD on your monitor. This setting only affects the OSD, the source material will be
displayed in its native format.
MONITOR TYPE
This setting sets the
MONITOR OUT
of the M15. Select between YUV, S-Video and CVBS. For source
inputs using both S-Video and CVBS, only YUV is available.
SUPERIMPOSE
You may superimpose the Setup OSD over any existing video by selecting ON. The OFF setting places the
OSD over a black background.
TEMP DISPLAY (TEMPORARY OSD)
One may display the operating state of the M15 temporarily by setting this variable to FULL. Otherwise
when the variable is set to SIMPLE only the volume OSD will display. A setting of OFF will disable the
temporary OSD.
Note:
To display a temporary OSD on the
MS OUT COMPOSITE VIDEO
, the TEMP DISPLAY may be
set to either SIMPLE or FULL.
TRIGGER SETUP
TRIGGER 1 & TRIGGER 2+3
There are two trigger assignments, Trigger 1 and Trigger 2+3. The trigger outputs can be assigned to;
POWER ON, ZONE 2, DVD, SAT, VCR, Video 4, Video 5, Video 6, Disc, CD, and Tuner.
POLARITY
One may assign the steady-state of the trigger polarity to either POLARITY variables HIGH or LOW. This
steady-state polarity is the ‘active’ final state of the trigger output signal.
DELAY (S)
The delay between when one selects the assignment either from the front panel or HTRM remote, to
when the trigger signal will transition. The values are in seconds, set from 0, 1, or 5 seconds.
DURATION (S)
The duration of the steady state may be set in seconds from 1, 5, 10, 30, to INFINITE.
TRIGGER INPUT
when the TRIGGER INPUT is set to ON, the M15 will turn on from the standby state when a DC +12V
signal is present at the
TRIGGER IN
socket. As long as the signal is present the M15 will remain in the
ON state. When the +12V signal is absent, the M15 will revert to its standby state.
Note:
The front panel button or the HTRM remote control can override the
TRIGGER IN
signal
ZONE 2/MS OUT
INPUT
Using the HTRM remote, select an input to display on the
ZONE 2/MS OUT
via this OSD menu. All inputs
other than tape monitor and ext. 7.1 can be selected at the
ZONE 2/MS OUT
using your HTRM remote
control in the main zone.
VOLUME
This volume setting is the temporary volume setting of the ZONE 2/MS OUT via HTRM remote control.
Adjust the level using the HTRM’s navigation arrows
or
from mute to +12 dB.
VOL DEFAULT (START UP ZONE 2 VOLUME)
This volume setting is the default volume setting from standby. The level may be set from mute to +12
dB using the same navigation arrows above. To store the value one must press the HTRM’s
ENTER
button.
USING THE M15
Setup
ENGLISH
FRANÇAIS
DEUTSCH
NEDERLANDS
ESP
AÑOL
IT
ALIANO
POR
TUGUÊS
SVENSKA
DISPLAY
SETUP
->
TV
SYSTEM
NTSC
->
MONITOR
TYPE
YUV
->
SUPERIMPOSE
ON
->
TEMP
DISPLAY
FULL
ZONE
2
->
INPUT
SAT
->
VOLUME -20.0dB
->
VOL DEFAULT
-20.0dB
DISPLAY
SETUP
->
TV
SYSTEM
PAL
->
MONITOR
TYPE
YUV
->
SUPERIMPOSE
ON
-> TEMP
DISPLAY
SIMPLE
ZONE
2
->
INPUT
SAT
->
VOLUME
-12.0dB
->
VOL DEFAULT
-20.0dB
TRIGGER
SETUP
->
TRIGGER 1
-> ASSIGNED
TO
POWER ON
->
POLARITY
HIGH
->
DELAY
(S)
0
->
DURATION (S)
INFINITE
->
TRIGGER INPUT ON
->
->TRIGGER
2+3
TRIGGER
SETUP
->
TRIGGER
2+3
-> ASSIGNED
TO
ZONE 2
->
POLARITY
HIGH
->
DELAY
(S)
1
->
DURATION (S)
INFINITE
M15 02 23 2006.qxd 3/7/2006 9:06 AM Page 32
