NAD C3050 LE, Руководство пользователя

Страница: 8 / 18

ENGLISH
IDENTIFICATION OF CONTROLS
FRONT PANEL
8
DEEP STANDBY MODE
At Deep Standby mode, the C 3050 LE switches to standby mode at lowest
power consumption (less than 0.5W).
SET C 3050 LE TO DEEP STANDBY MODE
1
At operating mode, press and hold the front panel POWER button until
the Power LED indicator flashes twice.
2
Release hold of front panel POWER button. Unit will go to Deep
Standby mode.
3
At Deep Standby mode, the C 3050 LE can be switched back to
operating mode using only the following methods.
• Press any of the SOURCE buttons
• Press front panel POWER or SR 10 ON button
4
The C 3050 LE switches to Network Standby mode when it is powered
up from Deep Standby mode. Repeat Step 1 to return C 3050 to Deep
Standby mode.
5 REMOTE SENSOR
•
Point the SR 10 remote control at the remote sensor and press the
buttons.
•
Do not expose the remote sensor of the C 3050 LE to a strong light
source such as direct sunlight or illumination. If you do so, you may
not be able to operate the C 3050 LE with the remote control.
Distance:
About 23ft (7m) from the front of the remote sensor.
Angle:
About 30 o in each direction of the front of the remote sensor.
6 TONE CONTROLS
•
The C 3050 LE is fitted with BASS and TREBLE tone controls to adjust
the tonal balance of your system. The 12 o’clock position is “flat” with
no boost or cut, and an indent indicates this position.
•
Rotate the control clockwise to increase Bass or Treble level. Rotate
the control counterclockwise to decrease Bass or Treble level.
7 SOURCE INPUT SELECTORS
•
These buttons select the active Source input to the C 3050 LE and
the signal sent to the speakers, headphones and the PRE OUT
sockets.
PHONO:
The turntable connected to the rear panel PHONO input
sockets is selected as the active Source.
LINE:
The line-level source connected to the rear panel LINE input
sockets is selected as the active Source.
OPTICAL:
The digital optical source connected to the rear panel
OPTICAL input socket is selected as the active Source.
COAX:
The digital coaxial source connected to the rear panel COAXIAL
input socket is selected as the active Source.
HDMI:
The HDMI output source connected to the rear panel HDMI
input socket is selected as the active Source.
8 SOURCE INPUT LED INDICATORS
•
When a Source input is selected, the corresponding Source input
LED indicator located above said Source input button will illuminate
green.
9 SPEAKERS (A, B, A+B, OFF)
Rotate SPEAKERS knob to select
A:
Select SPEAKERS A as the active speaker. SPEAKERS B is disabled or
inactive.
B:
Select SPEAKERS B as the active speaker. SPEAKERS A is disabled or
inactive.
A+B:
Select both SPEAKERS A and SPEAKERS B as the active speakers.
OFF
: Both SPEAKERS A and SPEAKERS B are inactive or disabled.
•
Output signal is always present at PHONES jack at all SPEAKER
selector settings. When using headphones, it is normally advisable
to set the SPEAKER selector control knob to “OFF” muting both
SPEAKERS A and B.
10 BALANCE
•
The BALANCE control adjusts the relative levels of the left and right
speakers. The 12 o’clock position provides equal level to the left and
right channels. A detent indicates this position.
•
Rotating the control clockwise moves the balance towards the
right. Rotating the control counterclockwise moves the balance to
the left.
11 BluOS/MDC
•
Press BluOS/MDC cap touch sensing button to select BluOS as the
active Source.
•
The LED indicator beside BluOS/MDC will show the status of BluOS.
If the LED is blue in color, it means it has network connection.
12 BLUETOOTH
•
This Bluetooth cap touch sensing button is not functional for now.
It will be activated in future software updates.
•
Select Bluetooth source via the BluOS App.
BLUETOOTH AS A SOURCE
Initiate pairing of your Bluetooth device with C 3050 LE by following below
procedure.
a
Ensure that the supplied Bluetooth antenna is connected to the BT
antenna terminal of the MDC2 BluOS D module. Ensure also that
your Bluetooth device is active or turned ON.
b
Using your iOS, Android or your Bluetooth device, go to Settings –
Bluetooth and then scan for Bluetooth devices.
c
Select the unique device ID of your C 3050 LE among the available
devices listed in your Bluetooth settings. Pair or connect together
your C 3050 LE and Bluetooth device.
d
Upon successful pairing of your Bluetooth device and C 3050 LE,
select Bluetooth source in the BluOS App and start listening to
music playback from your Bluetooth device.
13 VOLUME LEVEL LED INDICATORS
•
This series of LEDs illuminate one by one as the volume level
increases and extinguishes one by one as the volume level
decreases.
•
LED at amber alone indicates that the volume level is at the
minimum.
14 VOLUME
•
The VOLUME control adjusts the overall loudness of the signal sent
to the speakers and headphones.
•
The Volume control is characterized by perfect signal tracking and
channel balance. It provides a highly linear and low noise operation.
•
Turn clockwise to increase the volume level and counterclockwise
to lower it.