NAD C3050 LE Скачать руководство пользователя

Страница: 7 / 18

ENGLISH

1 NAD VU METER

•

The C 3050 LE is equipped with a pair of Power meters that
monitors the Input Signal or Speaker Output levels.

•

Both Power meters are calibrated in Watts and dB (decibel) that
corresponds to an 8-ohm load.

•

Refer also to item about VU METER in the IDENTIFICATION OF
CONTROLS – REAR PANEL.

2 POWER LED INDICATOR

•

This indicator will light up amber when the C 3050 LE is at standby
mode.

•

When the C 3050 LE is powered up from standby mode, this
indicator will illuminate green.

•

In cases of serious abuse of the C 3050 LE, such as excessively low
loudspeaker impedance and short circuit, the C 3050 LE will engage
its Protection circuitry, indicated by the Power LED turning from
green to red and the sound being muted.

In such Protection circuit scenario, turn OFF the C 3050 LE via the
rear panel POWER switch. Wait for it to cool down and/or check the
speaker connections. Once the cause for the protection circuitry
to engage has been removed, switch ON the rear panel POWER
switch. Then press the front panel POWER button to resume normal
operation.

3 PHONES

•

A 1/4” stereo jack socket is supplied for headphone listening and
will work with conventional headphones of any impedance.

•

The headphone socket will work in parallel with the selected
speakers. To listen to headphones only, rotate SPEAKERS knob to
OFF position.

•

The volume, tone and balance controls are operative for
headphone listening.

•

Use a suitable adapter to connect headphones with other types of
sockets, such as 3.5mm “personal stereo” jack plugs.

NOTE

Make certain that the volume control is turned to minimum (fully
counterclockwise with Volume Level LED Indicator only at amber color)
before connecting or disconnecting headphones. Listening at high
levels can damage your hearing.

4 POWER BUTTON

•

With the rear panel POWER switch set to ON position, press this
button to power up the C 3050 LE from standby mode. The Power
LED indicator will turn from amber to green. The NAD VU meter

will also illuminate from amber to white with yellow background.
The C 3050 LE is ready for operation when the NAD VU meter is
illuminated white with yellow background.

•

Pressing the Power button again turns the unit back to standby
mode. The Power LED indicator will change from green to amber
color. The NAD VU meter will also turn off.

•

The Power button cannot activate the C 3050 LE if the rear panel
POWER switch is off.

IMPORTANT NOTES

Conditions for Power button to activate

Connect the plug of the supplied power cord to a mains power
outlet while ensuring that the other end of the power cord is firmly
connected to C 3050 LE’s AC Mains input socket.

The rear panel POWER switch must be set to ON.

AUTO STANDBY

Auto Standby feature is an integral feature of C 3050 LE that conforms
to European ecodesign regulations. The C 3050 LE can be setup to
automatically go to standby mode if there is no user interface interaction
or no audio at current source within 15 minutes. Follow below procedure
to enable or disable auto standby mode. Refer also to Network Standby
mode below.

ENABLE/DISABLE AUTO STANDBY MODE

At operating mode, press and hold front panel PHONO button until
PHONO Source LED indicator flashes.

Enabled

– PHONO Source LED indicator flashes twice.

Disabled

- PHONO Source LED indicator flashes once.

NETWORK STANDBY MODE

The C 3050 LE is at network Standby Mode by default or after factory reset.
If there is no user interface interaction and no active source input within 15
minutes, the unit switches to Network Standby mode at reduced system
performance level (less than 2W).

•

Network and Bluetooth connections are maintained at network
standby mode.

•

At Network Standby mode, the C 3050 LE can be switched back to
operating mode using any of the following methods.

•

Resume playback of analog or digital sources

•

Activate or play network connected App

•

Play paired Bluetooth source

•

Press any of the SOURCE buttons