ENGLISH
8 PHONO IN
•
Input for a Moving Magnet (MM) phono cartridge only. Connect the
twin RCA-to-RCA lead from your turntable to this input if you are
using a Moving Magnet cartridge.
•
If your turntable includes a ground/earth lead, it can be connected
to the Ground Terminal.
9 GROUND TERMINAL
•
Ensure that the C 3050 LE is plugged-in to a grounded AC wall outlet.
•
If necessary, use this ground terminal to connect to ground a
phono or turntable source for PHONO input.
•
If a separate earth ground is necessary, use this terminal to ground
your C 3050 LE. The C 3050 LE can be connected to ground by
connecting a ground lead wire or similar to this terminal. After
insertion, tighten the terminal to secure the lead.
10 LINE IN
•
Input for line level sources such as CD player, tuner or any
compatible devices. Use dual RCA-to-RCA lead to connect the
source device’s left and right “Audio Output” to this Line input port.
11 MAIN IN
•
Connections to an external preamplifier or processor, such as a
surround sound decoder.
•
In normal use, this should be connected to the PRE OUT sockets
with the links supplied. To connect your C 3050 LE to an external
processor or preamplifier, remove first these links.
•
Use dual RCA-to-RCA lead to connect the left and right “Audio Output” of
the external preamplifier or processor to the MAIN IN sockets.
•
Always turn OFF the C 3050 LE and associated external
preamplifiers before connecting or disconnecting anything to the
MAIN IN sockets.
12 PRE OUT
•
Use dual RCA-to-RCA lead to connect PRE-OUT to the
corresponding analog audio input of compatible devices such
as amplifiers, receivers or other applicable devices. This makes it
possible to use the C 3050 LE as a preamplifier to such devices.
•
In normal use, this should be connected to the MAIN IN sockets
with the links supplied. To connect your C 3050 LE to an external
processor or amplifier, remove first these links.
•
The PRE OUT output signal will be affected by the C 3050 LE’s
volume and tone control settings.
•
Always turn OFF the C 3050 LE and associated external power
amplifiers before connecting or disconnecting anything to the PRE
OUT sockets.
13 SUBW
•
Connect SUBW to the low level input of corresponding powered
subwoofer.
•
Low frequency information up to 80 Hz is sent to the connected
subwoofer.
14 SPEAKERS A, B
•
The C 3050 LE is equipped with two sets of speaker terminals.
Use the SPEAKERS A terminals for the “main” speakers and use the
SPEAKERS B terminals for a second pair, for example, extension
speakers located in another room.
•
Connect C 3050 LE’s Right speaker terminals marked “R +” and “R-”
to the corresponding “+” and “ - “ terminals of your designated right
speaker. Repeat the same for C 3050 LE’s Left speaker terminals and
corresponding left speaker.
•
Double check the speaker connections before powering up the
C 3050 LE.
•
Refer also to item about SPEAKERS SELECTOR (A, B, A+B, OFF) in the
IDENTIFICATION OF CONTROLS – FRONT PANEL.
15 AC MAINS INPUT
•
The C 3050 LE comes supplied with two separate mains power
cords. Select the mains power cord appropriate for your region.
•
Before connecting the plug to the mains power outlet, ensure that
the other of end of the power cord is firmly connected to the C
3050 LE’s AC Mains input socket.
•
Always disconnect the mains power plug from the mains power
outlet before disconnecting the other of end of the power cord
from the C 3050 LE’s AC Mains input socket.
16 FUSE HOLDER
•
Only qualified NAD service technicians can have access to this fuse
holder. Opening this fuse holder may cause damage thus voiding
the warranty of your C 3050 LE.
17 BLUETOOTH ANTENNA TERMINAL
•
This Bluetooth antenna terminal is not applicable for C 3050 LE. It
maybe activated in future software updates.
18 SERVICE
•
Service port is for internal use only and not for customer use.
19 IR IN
•
This input is connected to the output of an IR (infrared) repeater
(Xantech or similar) or the IR output of another compatible device
to allow control of the C 3050 LE from a remote location.
20 +12V TRIGGER OUT
•
The +12V TRIGGER OUT is used for controlling external equipment
equipped with a +12V trigger input.
•
Connect this +12V TRIGGER OUT to the other equipment’s
corresp12V DC input jack using a mono cable with 3.5mm
male plug.
•
This output will be 12V when the C 3050 LE is ON and 0V when it is
either OFF or in standby mode.
21 VU METER
•
Directs the NAD VU meter in the front panel to monitor Input Signal
or Speaker Output
Input Signal:
Monitor and reflect current Source input signal
Speaker Output:
Monitor and reflect Speaker Output signal
22 POWER
•
Supplies the AC mains power to C 3050 LE.
•
When the POWER switch is set to ON position, the C 3050 LE goes
to standby mode as shown by the amber status condition of the
front panel Power LED indicator.
•
Press the front panel Power button, SR 10 ON button or any of the
Source Input selector buttons to power up the C 3050 LE from
standby mode.
•
If you do not intend to use the C 3050 LE for long periods of time
(such as when on vacation), switch off the POWER switch.
•
With rear panel POWER switched OFF, the C 3050 LE cannot be
powered up by the front panel Power button, SR 10 ON button or
any of the Source Input selector buttons.
IDENTIFICATION OF CONTROLS
REAR PANEL
10
Содержание C3050 LE
Страница 1: ...Owner s Manual ENGLISH Stereophonic Amplifier C3050 LE ...
Страница 17: ...ENGLISH 17 ...