Nabtesco RV N Series Скачать руководство пользователя | Manualshive

Страница: 46 / 62

background image

Chapter 6 Filling the Lubricant

38

Step 5

Rotate the output shaft of the reduction gear by 1 or 2 turns.



Do not use the motor to rotate the output shaft of the reduction gear for safety, if possible. If the
motor is used by necessity, run the motor at a low speed and never touch the rotation section.
Otherwise, you could be caught by the rotation section, which will result in serious injury.

Step 6

Repeat

steps 1 to 5

until the lubricant is filled up to the specified level.

Step 7

After filling the lubricant up to the specified level, wipe the lubricant off from the tapped holes for

injecting/draining grease and cap them with plugs sealed with a seal tape, etc.

Fig. 6-3

Horizontal shaft installation

Vertical shaft installation

(with shaft facing downward)

Vertical shaft installation

(with shaft facing upward)

Shaft
installation
component

Shaft installation component

Shaft installation
component

Filler

Filler

Filler

Motor mounting flange

Motor mounting flange

Motor mounting flange

Tapped hole for injecting/draining

grease (supply side)

Tapped hole for injecting/draining
grease (drain side)

Tapped hole for injecting/draining
grease (drain side)

Tapped hole for
injecting/draining
grease (drain side)

Tapped hole for injecting/

draining grease (supply side)

Tapped hole for injecting/

draining grease (supply side)

«
...
44
45
46
47
48
...
»

Содержание RV N Series































































Отзывы:

Нет отзывов

Похожие инструкции для RV N Series

Бренд: Labnet Страницы: 5

Бренд: Napoleon Страницы: 2

Бренд: Raytheon Страницы: 62

Бренд: HALDER Страницы: 2

Бренд: Hakko Electronics Страницы: 16

Бренд: olympia electronics Страницы: 4

Бренд: GE Страницы: 176

Бренд: Triton Blue Страницы: 11

Бренд: Tadano Страницы: 16

Бренд: 2connect Страницы: 8

Granudos 45/100-Touch

Бренд: WDT Страницы: 138

66TX51341313131

Бренд: Neumo Страницы: 92

Бренд: VWR Страницы: 13

Бренд: MA lighting Страницы: 45

Бренд: Spectra Страницы: 2

Бренд: KTR Страницы: 13

ANTS REPELLER HOME

Бренд: Radarcan Страницы: 2

Бренд: Yacht Devices Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды