Nabtesco RV N Series Скачать руководство пользователя

Страница: 55 / 62

Appendix: Design Scheme of Input Gear



Selection of the input gear type

There are the following two types of standard input gear:

Standard input gear A: For small motors
Standard input gear B: For large motors

Select the type of input gear to be used by referring to the tables below.

Applicable motor shaft diameters
for standard input gear

(Unit: mm)

Model

Standard input gear

Model

Standard input gear

RV-25N

Less than ø28

ø28 or more

RV-125N

ø42 or less

RV-42N

Less than ø32

ø32 or more

RV-160N

ø48 or less

RV-60N

Less than ø32

ø32 or more

RV-380N

Less than ø55

ø55 or more

RV-80N

Less than ø38

ø38 or more

RV-500N

Less than ø55

ø55 or more

RV-100N

ø42 or less

RV-700N

Less than ø55

ø55 or more

Note: Some models have only standard input gear A.



Design of the motor shaft hole

(Design example 1: For straight shafts (attached to motor shaft tip)>

Note

1. When a tapped hole is used for the motor shaft, fix the input gear to the motor shaft with a bolt.

2. For the bolt through hole diameter (d3), radial runout, and the shaft hole position (LC), refer to “Dimensions after

modification” in the “Dimensions” table on pages 48 and 49.

3. If the bolt through hole diameter (d3) is larger than the center hole diameter on the tooth surface side (d4), it is

necessary to process the carburized surface. In such a case, confirm the applicable tools and processing conditions, etc.

4. The clearance hole diameter for the key slot (d5) is “key slot width (k) + 2 mm”, approximately. [The clearance hole

diameter must be larger than the key slot width (k).]

5. Design the motor shaft hole diameter (d1) according to the motor shaft diameter to be used.

6. For the key slot width (k) and key slot height (a), refer to the specifications of the key to be used.

Image of assembly

Detailed drawing of section E

Drill both at the
same time

d5 drill

Installation

reference surface

Clearance

Содержание RV N Series































































Результаты поиска

Содержание RV N Series

Отзывы:

Похожие инструкции для RV N Series

Бренды по названию

Популярные бренды

Nabtesco RV N Series, Руководство по эксплуатации

Результаты поиска

Содержание RV N Series

Отзывы:

Похожие инструкции для RV N Series

Бренды по названию

Популярные бренды