Nabco GYRO TECH GT-1175, Быстрая настройка, Страница: 21 / 53

21 of 53
www.NabcoEntrances.com GT1175 (H105 Medium) Hurricane Quick Set-Up and Parts Guide
Rev 8-10-16 P/N C-00106
AC 115V ± 10%
50 / 60 Hz
Ground Wire
Auxiliary 120 VAC Power wires
(These wires normally coiled and  ed up)
On/Off
Power Switch
DN 0647
U30 Microprocessor Control
P/N V-00020
0 7
1
2 3
4
5 6 7
8
9
10
11 12
>PO
M<
NAB CO
GYR O TECH
DS-1500
D24-113270
Nabtesco Corporation
MADEI N JAPAN
NA
BCO
NABCO
CAUTION !
RELA
TED DEVICE
S
･
16
P
12
13
14
15
16
No.
11
10
9
8
7
6
5
4
3
2
1
SYMBOL
H
M0
9DC12V
SQ
OUT
Common
N/C
N/O OUT.A
OUT.B
OUT.C
7
BA
62
SLS
M1
6B
7
61
Sequential Activation
Auxiliary Output (Open-Collector)
5Amax.(0-20V), 3.2Amax.(20-30V)
30V(42.4Vpeak)max.
Contact Output (Class2 Load only)
12VDC-(Common)
FUNCTION [SLIDING DOOR]
Reduced Opening Switch
Breakout Detector
Sidelite Presence Sensor
Exterior Activation
Holding Beam
Interior Activation
12VDC-(Common)
12VDC+
Mode Switch (see Mode SW Usage shown left)
HANDY TERMINAL ･ 6P No.
248901-
Microprocessor Controller
Mode SW Usage
Gnd
Gnd Gnd
Open
Open
Open
Gnd
Open
M0 M1 MODE
TWO WAY
ONE WAY
NIGHT
HOLD OPEN
To protect against risk of fire
or electric shock,use only the
certified NABCO power supply.
WARNING
MOTOR ･ 12P
ERROR
POWER
BA
62
H
6B
61
INDICA
TO
RS
POWE
R
･
2P
Do not disassemble the control box.
There are no user serviceable parts
inside.
To maintain warranty,repairs must be
made by authorized NABCO facilities.
Adjustments to the door can only be made
with the NABCO Handy Terminal.
20VA
C 50/60H
z
GYRO TECH
NABC O
!
!
!
!
TB1
NOISE
FILTER
TB2
T1
S1
PE
N
L
LO
AD
-CIRCUIT-
-BREAKER-
RED INDICATES
POWER IS OFF
PRESS
TO
RESET
POWER SUPPLY
ASSEMBLY
P/N 9418800100
NABCO
14-11741
ENTRANCES, INC.
Power Supply
P/N V-00029
Motor/Operator
P/N M-00395
120 VAC
4. Go to the TB1 Port located on the Left side of the Power Supply Module.
5. Insert the Incoming 120 VAC Black (HOT) wire into the Circuit marked “L”.
6. Insert the Incoming 120 VAC White (Neutral) wire into the Circuit marked “N”.
7. Insert Green (Grounding) wire into the Circuit marked “PE”.
8. Ensure the Slide door system is Grounded for safe and consistent operation.
8 .1 Determine Correct Handing
1. With power OFF, manually slide the door half way open.
2. Turn power ON. The Slide door should slowly close (per Power On factory settings).
8 .2 Correct Wrong Handing
1. With the power ON, obtain the Cable from the Handy Terminal Case.
2. Go to the Handy Terminal Harness that is connected to the U30 Microprocessor Controller. Remove the protective Cap.
3. Connect the plug end of the Cable (that is protected with a metal sleeve), to the socket of the Handy Terminal Harness.
a. The plug end of the Cable has multiple prongs that need to line up with the socket. Gently turn the plug end clockwise
while trying to insert it until a connection can be made.
4. Connect the other end of the Cable to the Handy Terminal.
5. Press: ENTRY until the screen displays: SPECIAL FUNCTION ADJUSTMENTS Then select: Y
6. Continue pressing: ENTRY until the Screen displays: RECYCLE Change the setting.
7. Disconnect the Handy Terminal.
a. Wait at least (10) seconds before disconnecting Handy Terminal to allow last test to complete and message display
to stabilize.
8. With power OFF, manually slide the door half way open.
9. Turn power ON. The Slide door should slowly close (per Power On factory settings).
10. Plug the Handy Terminal back into the Terminal Connector.
DN 0435
Connect Cable to Handy Terminal
Remove Protec ve Cap from Harness
Handy Terminal Harness
U30 Microprocessor Controller
Handy Terminal
Cable