MYERSON FlexPress Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 24

MYERSON FlexPress Скачать руководство пользователя страница 7

section 7 ~ myerson DuraFlex partial

injection procedure

The following procedure outlines the steps necessary to create

myerson

DuraFlex

Partials with the

myerson

Flexpress

™ Digital

Injection System.

1. Evaluate the model for major undercuts and block out the

undercuts. Due to the flexibility and adjustability of the material,

very little if any blocking out will be needed.

2. Paint the model with myerson Thermoplastic Model Separator

MS-0200

.

7

section 6 ~

processing using the

“Re-run Last Profile”

1. From the main menu use the

UP or DOWN

buttons until the cursor

is to the left of “Rerun Last Profile” then press the enter button.

2. The display will show the profile name and profile settings of the

last injection. If this is not the profile you wish to run, press the

LEFT arrow button to return to the main menu.

3. The

myerson

Flexpress

™ is now ready to process your case.

See steps 5-13 of Section 5 for a complete injection.

12. Press the

EXTEND/RETRACT

button again to retract the piston.

13. The

myerson

Flexpress

™ is now ready to process another case.

Repeat steps 1-9 for your next injection.

«
...
5
6
7
8
9
...
»

Содержание FlexPress

























Отзывы:

Нет отзывов