manualshive.com logo in svg

MYERSON FlexPress, Инструкция по эксплуатации, Страница: 23 / 24

Поделиться
Скачать
MYERSON FlexPress Скачать руководство пользователя страница 23

23

Framework

Bridges

Crowns

Clasps

Unilaterals

myerson SPECIAL

Premium quality teeth hand-crafted to be 

virtually indistinguishable from natural teeth

 

myerson DB PLUS

 

Time proven formula reinforced with 

sub-micron silica to enhance hardness

 

KENSON

“The Professional Choice” for over 50 years; 

Life-like aesthetics, unparalled value

ema

®

 is a trademark of frantz design inc

.

You could be using the 

myerson ema oral 

appliance

 for the treatment of sleep related 

breathing disorders. 

ema’s

 patented design 

uses interchangeable elastic straps attached 
to pressure-formed custom upper and lower 
trays, which allow the gradual advancement 
of the mandible until treatment is successful.  

myerson ema oral appliance

 is available 

to medical and dental professionals through 
authorized dental laboratories. 

jim please check this copy....

more to myerson than teeth
www.myersontooth.com

english. français. español. italiano.

Elastic straps vary in length and  
elasticity: 20 choices in all

Bite pads increase  
vertical opening

Maximum room for tongue

Partial Dentures 

Содержание FlexPress

























Отзывы:

Нет отзывов