manualshive.com logo in svg

MYERSON FlexPress, Инструкция по эксплуатации, Страница: 6 / 24

Поделиться
Скачать
MYERSON FlexPress Скачать руководство пользователя страница 6

6

section 5 ~  

Processing using the 

    “Run Stored Profile”  

      (Recommended Option)

1.  From the main menu use the 

UP or Down

 buttons until the 

 

“Run Stored Profile” is displayed then press the enter button.

2.  Next use the 

UP/DOWN

 buttons until profile you wish to run 

 

s displayed.

3.  After selecting the profile the display will show the profile name.
 

Pressing 

ENTER

 will scroll between profile name, melt tempera-

 

ture, melt time and hold time. It is recommended to check the 

 

setting before starting a profile.

4.  Press the 

START

 button and the machine will begin running the  

 

 

profile. If the machine is at room temperature, it will take approxi-   

 

mately 15 minutes to reach the processing temperature. 

5.  Prepare the cartridge by scoring 
 

a “+” using a utility knife. 

 

See the illustration to the right. This will 

 

create an even “Burst” of the cartridge

6.  Next, coat the sides of the cartridge 
 

with a light coat of release  compound. 

 

This will prevent the cartridge from sticking 

 

to the walls of the heating chamber.

7.  When the 

myerson

 

Flexpress

 has calibrated itself at the Melt 

 

Temp an alarm will sound and the upper display will read 

“LOAD”

 

signaling you to load the cartridge. At this time insert the cartridge

 

into the heating chamber, center the flask and tighten using the

 

flask strap and knobs. If you are not ready to start the profile at

 

this time and want to turn off the alarm, press the UP button. 

 

This will silence the alarm, but the myerson 

Flexpress

™ will 

 

remain calibrated until you press 

START 

or put the unit in standby    

 

by pressing the STBY button.

8.  Press the 

START

 button to begin the profile. Now let the 

myerson

 

Flexpress

™ do the rest. The unit will begin counting down the 

 

Melt Time and once it expires the unit will automatically inject the

 

material into the flask. The piston will stay in the up position for

 

the duration of the Hold time then release.

9.  The upper display will read 

“DONE”

.

10.  You can now remove the flask strap and knobs. 
11.  Grasp the flask using heat resistant gloves and press the 
 

EXTEND/RETRACT

 button. This will extend the piston and 

 

push out the remaining cartridge attached to the flask.

Содержание FlexPress

























Отзывы:

Нет отзывов