MyBinding Duplo DF-920 Скачать руководство пользователя | Manualshive

Страница: 51 / 65

background image

48

18. WHEN PAPER JAMMING OCCURS

18-1. When Paper Jams

at Paper Feed Section

The LCD shows “FEED ERROR”.

If the top cover, side cover, or paper ejection section cover has been opened to remove jammed paper as
described below, be sure to close it after removing. This unit will not operate if covers are open and the LCD will
show an error message such as “TOP COVER OPEN”.

Note

Note

FEED ERROR

Open the top cover, and pull out paper
jammed near the paper feed ring. After
removal, close the top cover.

If the paper jams again, increase the paper
feed pressure using the paper feed pressure
adjusting lever.

Top cover

Top cover

18-2. When Paper Jams

Near Paper Feed Ring

The LCD shows “JAM FEED SECT”.

JAM FEED SECT

Open the top cover, and pull out paper
jammed near the paper feed ring. After
removal, close the top cover.

If the paper cannot be pulled out easily,
lower the paper feed tray by removing all the
paper on the paper feed tray, or by using the
following keys, and then pull out the paper.

Raising/lowering the paper feed tray using
the control panel

To lower the paper feed tray, press the “–” key of the folding
plate 1 folding stopper adjusting key while pressing the stop
key. To raise, press the “+” key.

«
...
49
50
51
52
53
...
»

Содержание Duplo DF-920


































































Отзывы:

Нет отзывов

Похожие инструкции для Duplo DF-920

Бренд: NanaWall Страницы: 22

Tekken Tag Tournament

Бренд: NAMCO Страницы: 59

Бренд: NAMCO Страницы: 29

MO-6800DD10 Series

Бренд: JUKI Страницы: 47

Бренд: Bulldog Security Страницы: 7

Stairville VF-1200 DMX VertiFog CO2 FX

Бренд: thomann Страницы: 40

Ninja warrior 1200PSI NWCU1312N

Бренд: Prochem Страницы: 44

Бренд: Sandia Страницы: 2

Бренд: Yamato Страницы: 40

Бренд: JUKI Страницы: 4

Бренд: JUKI Страницы: 100

Бренд: Koblenz Страницы: 8

Бренд: Panasonic Страницы: 13

Бренд: Panasonic Страницы: 41

KX FP205 - B/W Thermal Transfer

Бренд: Panasonic Страницы: 52

Бренд: Panasonic Страницы: 64

KX FP145 - Slim-Design Fax Machine

Бренд: Panasonic Страницы: 86

Бренд: Panasonic Страницы: 110

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды