MVP Patriot Megaject Innovator II Скачать руководство пользователя страница 51

Страница: 51 / 78

Patriot Megaject Innovator II Operations Manual

Rev. 04/2014

Page | 51

SP4 Solvent Pump Air Vent tube

– this

exhausts air from the SP4 through the

flush valve and protects air system for

solvent contamination.

Fig. 23

Fig. 24

On the inside of the flush tank the there are two (2) connections to the flush pump.



The pump inlet air tube connects to the inlet side of the SP4 solvent pump through

the inlet fitting.



The Yellow flush tube from the injection gun / mix head extends down through the

outlet side fitting and connects to the outlet of the solvent pump.

Note: it is important that the solvent level in the tank be at no less then 1/3 full or
so that t

here is 25mm (1”) of solvent above the SP4 solvent pump. This will allow

the SP4 solvent pump to properly refill with solvent after each use.

Maintenance

–

The SP4 Solvent Pump is basically maintenance free however it might

be necessary to replace the O-ring (0464) on the Pump Foot Valve (4481).

It is important to keep the inside of the flush tank clean and free of dirt, debris and glass
fiber as these can prevent the Pump Foot valve from sealing properly.

Содержание Patriot Megaject Innovator II















































































Результаты поиска

Содержание Patriot Megaject Innovator II

Отзывы:

Похожие инструкции для Patriot Megaject Innovator II

Бренды по названию

Популярные бренды

MVP Patriot Megaject Innovator II, Руководство по эксплуатации

Результаты поиска

Содержание Patriot Megaject Innovator II

Отзывы:

Похожие инструкции для Patriot Megaject Innovator II

Бренды по названию

Популярные бренды