MVP Patriot Megaject Innovator II Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 78

background image

Patriot Megaject Innovator II Operations Manual

Rev. 04/2014

Page | 19

CONTROL BOX INSTUCTIONS:

Overview of controls:

The Innovator control panel is shown in figure 4. Controls have been grouped based
upon function, to make the system as user friendly as possible. Reference the
“Innovator II Manual” for complete details on the Innovator II Control Box.

A brief overview of controls is as follows:

Emergency Stop:



Push button:

Press this button in the event of an emergency to place the system

in a safe state. Twist and pull to release and allow machine operation.

Pump pressure:



Pressure gauge:

This is the air pressure being supplied to the pump.



Regulator:

Adjust this to control the air pressure being supplied to the pump and

set the pump speed.

Flush/Alarms:



CAT OP VALVE:

Indicator will turn red if overpressure state exists.



RGA ALARM:

Indicator will turn red if gel alarm timer has expired.



Pushbutton:

Press this button to operate the flush cycle.

Mold Pressure Guard:



Preset level gauge:

Control signal air pressure being supplied to Mold Pressure

Guard (MPG) control.



Regulator:

Use this to adjust the MPG control signal air pressure.

Start/Stop Controls:



Inject:

Press to start the machine in inject mode.



Recirculate:

Press to start the machine in recirculation mode.



Stop:

Press to stop the machine in injection, recirculation or flush modes.

Stroke Counter:



Set a predetermined stroke count for the machine to stop at.

«
...
17
18
19
20
21
...
»

Содержание Patriot Megaject Innovator II















































































Отзывы:

Нет отзывов

Похожие инструкции для Patriot Megaject Innovator II

Бренд: OfiTE Страницы: 21

Бренд: Earthlite Страницы: 4

Бренд: YATEK Страницы: 78

Бренд: DARAY Страницы: 28

Бренд: MacDon Страницы: 88

Бренд: Jiffy Страницы: 15

Litmann Quality 3100

Бренд: 3M Страницы: 2

Бренд: Cambridge Audio Страницы: 2

Бренд: Quanser Страницы: 12

Бренд: olympia electronics Страницы: 4

SpinVessel VP 418SV3-1-850RB-CC

Бренд: V&P Scientific Страницы: 9

MACDON C HARVESTEC 6000

Бренд: CORN Страницы: 24

Бренд: Star Страницы: 16

Бренд: Mindray Страницы: 295

Бренд: ZAMST Страницы: 14

Бренд: Metrohm Страницы: 42

Бренд: Maquet Страницы: 232

TRAKTOR KONTROL S3

Бренд: Native Instruments Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды