MUTOH VJ-626UF Скачать руководство пользователя

Страница: 91 / 144

How to wear the supplied gloves 91

Wearing the gloves and goggles

Skin or eye contact with UV curable ink may cause skin inflammation or allergic reaction.
Wear protective gloves, goggles and/or face shield, and clothing while using of the printer.

Especially when performing any of the following operations, be sure to wear the supplied gloves (or solvent resistant gloves)
and goggles.

•

"Agitating ink cartridges" on page 92

•

"Replacing ink cartridge" on page 95

•

"Emptying waste ink tank" on page 96

•

"Performing Daily Maintenance" on page 102

•

"Clean daily maintenance parts" on page 109

•

"Replacing absorption material for the flushing box" on page 116

•

"Replacing the cleaning wiper" on page 119

How to wear the supplied gloves

Wear the rubber gloves (white) over the plastic gloves (pink).

Do not touch uncured UV ink with bare hands.

• If glove becomes contaminated with ink, replace it with new.

• If protective clothing becomes contaminated with ink, immediately remove and wash for re-use.

• If ink gets on skin, immediately wash with soap and plenty of water for 15 minutes.

Seek medical advice/attention if irritation or inflammation are present.

• If ink gets in eyes, flush eyes with plenty of water for 15 minutes and seek medical advice/attention

immediately.

• If swallowed, rinse mouth immediately and do not induce to vomiting.

Seek medical advice/attention.

Wearing the gloves and goggles

CAUTION

Содержание VJ-626UF

















































































































































Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды

MUTOH VJ-626UF, Руководство по эксплуатации

Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды