Murata WIT2410NF Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 58

background image

Declaration of Conformity

Warning! The RLAN transceiver within this device uses a band of frequencies that are not completely harmonized
within the Eur

opean Community. Before using, please read the European Operation Section of the Products User’s

Guide for limitations.

0889 is the identification number of RADIO FREQUENCY INVESTIGATION LTD - Ewhurst Park, Ramsdell RG26
5RQ Basingstoke, United Kingdom

– the Notified Body having performed part or all of the conformity assessment on

the product.

The WIT2410 to which this declaration relates is in conformity with the essential requirements of the R&TTE
directive 1999/5/EC and complies with the following standards and/or other normative documents:

For Interfaces

For RLAN Transceiver

EN 55022
EN 55024

EN 300 328
EN 301 489 -1, -17
EN 60950

Use Within the European Union

The WIT2410 is intended for use within the European Community States and in the following non-European Union
States: Norway & Switzerland

Use of the WIT2410 in France

When used in France, the WIT2410 can only be operated with the France hopping pattern selected. This is
accomplished by setting the

pe

parameter to 1. Refer to

European Union Settings

in this manual for details.

Canadian Department of Communications Industry Canada (IC) Notice

Canadian Department of Communications Industry Canada (IC) Notice
This apparatus complies with Health Canada’s Safety Code 6 / IC RSS 102.

"To prevent radio interference to the licensed service, this device is intended to be
operated indoors and away from windows to provide maximum shielding. Equipment (or
its transmit antenna) that is installed outdoors may be subject to licensing."

ICES-003

This digital apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus as set out in the radio interference regulations of Industry Canada.

Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables aux appareils
numériques de Classe B prescrites dans le règlement sur le brouillage radioélectrique édicté par Industrie Canada.

«
1
2
3
4
5
...
»

Содержание WIT2410NF



























































Отзывы:

Нет отзывов

Похожие инструкции для WIT2410NF

DigitalFlow XGS868i

Бренд: Panametrics Страницы: 86

Бренд: FAAC Страницы: 2

Бренд: Sangean Страницы: 1

Бренд: Sandstrom Страницы: 4

Бренд: K&K Sound Страницы: 6

Бренд: Yaesu Страницы: 35

Бренд: Oxygen Страницы: 2

Micro Link 49085D

Бренд: Xantech Страницы: 4

Бренд: MIRPO Страницы: 8

Бренд: Icom Страницы: 32

Бренд: Danfoss Страницы: 2

Бренд: YBA DESIGN Страницы: 54

Бренд: Zamel Страницы: 21

Бренд: Telemotive Страницы: 31

Бренд: Analog Devices Страницы: 82

DpharpEJX vigilantplant EJX510A

Бренд: YOKOGAWA Страницы: 49

Бренд: REnex Technology Страницы: 25

Бренд: Continental Automotive Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды