Murata WIT2410NF Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 58

background image

Important Regulatory Information

Murata Electronics Product FCC ID: HSW-2410NF

IC 4492A-2410NF

FCC s MPE Requirements

Information to user/installer regarding FCC s Maximum Permissible Exposure (MPE) limits.

Notice to users/installers using the following fixed antennas, with Murata RF products:

The field strength radiated by any one of these
antennas, when connected to Murata RF
products, may exceed FCC mandated RF
exposure limits. FCC rules require
professional installation of these antennas in
such a way that the general public will not be
closer than 2 m from the radiating aperture of
any of these antennas. End users of these
systems must also be informed that RF
exposure limits may be exceeded if personnel
come closer than 2 m to the apertures of any of
these antennas.

Notice to users/installers using the following mobile antennas, with Murata RF products:

Ace 2dBi dipole,

MobileMark 12 dBi Corner Reflector
(rebranded and Marketed as Invivo Corporation
Corner Reflector)

The field strength radiated by any one of these
antennas, when connected to Murata RF
products, may exceed FCC mandated RF
exposure limits. FCC rules require professional
installation of these antennas in such a way
that the general public will not be closer than
20 cm from the radiating aperture of any of
these antennas. End users of these systems
must also be informed that RF exposure limits
may be exceeded if personnel come closer
than 20 cm to the apertures of any of these
antennas.

Note:

This unit has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.  This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in  accordance  with  the  instruction  manual,  may  cause  harmful  interference  to  radio
communications.    Operation  of  this  equipment  in  a  residential  area  is  likely  to  cause  harmful
interference in which case the user will be required to correct the interference at their expense.

«
1
2
3
4
...
»

Содержание WIT2410NF



























































Отзывы:

Нет отзывов

Похожие инструкции для WIT2410NF

Бренд: Panasonic Страницы: 24

Бренд: M-system Страницы: 5

Бренд: LaserLiner Страницы: 40

Бренд: LabSat Страницы: 2

Бренд: Yamaha Страницы: 8

Бренд: Yaesu Страницы: 5

Бренд: Yaesu Страницы: 80

Бренд: R.V.R. Elettronica Страницы: 34

Бренд: Flying Industry Development Страницы: 3

Бренд: Cactus Страницы: 45

Бренд: Nexa Страницы: 41

Бренд: M-system Страницы: 3

Бренд: Harman Kardon Страницы: 15

FLEX-6000 Signature Series

Бренд: FlexRadio Systems Страницы: 24

Бренд: Muzak Страницы: 3

Бренд: Elvox Страницы: 8

Бренд: Tecsun Страницы: 12

Бренд: Camille Bauer Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды